Holiday Bonus: an extra 5% off every volume deal

Applied automatically in your cart, no code needed · Ends Tue, Nov 24

How to Apply Gel Stain (General Finishes Guide)

Infinity Cutting Tools |

General Finishes Gel Stain is one of the most forgiving ways to add rich, even color to wood, and it can even go over an existing finish without stripping. Because it's thick, it sits near the surface instead of soaking in, so it resists the blotching you often get with liquid stains on pine, maple and cherry.

Here's how to apply gel stain step by step, on bare wood and over old finishes, and how to topcoat it.

What Is Gel Stain?

Gel stain is a heavy-bodied, oil-based stain with a pudding-like consistency. General Finishes describes it as the stain with the most "finishing feel" of all their products.

Because it doesn't penetrate as deeply as a liquid wiping stain, it gives deep, rich color with very little blotching, and it won't run on vertical surfaces like cabinet doors and table legs.

General Finishes High Performance Top Coat

Gel Stain vs. Liquid Stain

Gel stain Liquid wiping stain
Consistency Thick, doesn't drip Thin, runs easily
Penetration Sits mostly on the surface Soaks into the wood
Blotching Minimal, even on blotch-prone woods Common on pine, maple, birch and cherry
Over existing finishes Yes, after cleaning and scuff-sanding No, it needs bare wood to absorb
Grain definition Softer, more uniform color Highlights the grain more

What You'll Need

How to Apply Gel Stain on Bare Wood

  1. Sand. Sand to 180 or 220 grit and remove all dust.

    Gel stain shows sanding scratches less than liquid stain, but a smooth surface still gives the best result.

  2. Stir the can. Mix thoroughly so the color is even from top to bottom.
  3. Apply a liberal coat with a cloth, foam brush or pad.

    Work one section at a time, such as a drawer front or tabletop.

  4. Wipe off the excess with a clean cloth, moving with the grain. Remove all rag marks and smudges before moving to the next section.
  5. Let it dry. Wait at least 24 hours between coats.

    Drying is faster in warm, dry conditions and slower in cold or damp ones.

  6. Add coats for deeper color. Apply and wipe additional coats until you reach the depth of color you want.

How to Apply Gel Stain Over an Existing Finish

Gel stain is popular for updating kitchen cabinets and furniture without stripping.

Products like Java Gel Stain are especially popular for this kind of makeover.

  1. Clean thoroughly. Remove grease, wax and grime. Kitchen cabinets in particular need a good degreasing.
  2. Scuff-sand. Lightly sand the existing finish with a fine sanding sponge so the stain has something to grip.

    You're dulling the sheen, not removing the finish.

  3. Test. Try the stain on a hidden area, such as the back of a door, to check adhesion and color.
  4. Apply thin coats. Apply and wipe as above.

    Over an existing finish, 2 to 3 coats are typical. Let each coat dry at least 24 hours.

Topcoating Gel Stain

Gel stain can be used as a one-can finish, but a topcoat adds durability, especially on tabletops and cabinets that get handled every day.

  • Water-based topcoats: General Finishes recommends letting the last coat of stain dry for 48 hours before applying Gel Satin or High Performance Top Coat. Apply 2 to 3 coats.
  • Oil-based topcoats: An oil and urethane finish like Arm-R-Seal is a natural partner for oil-based gel stain.

    Make sure the stain is fully dry first.

  • Don't rush it. Topcoating over stain that isn't fully dry is the most common cause of a cloudy or hazy finish.

Tips for a Flawless Gel Stain Finish

  • Work in small sections so the stain doesn't start to set before you wipe it.
  • Always make your final wipe with the grain.
  • Keep a wet edge on large surfaces to avoid lap marks.
  • Clean up with mineral spirits.
  • Lay used rags flat to dry outdoors or store them in a sealed, water-filled metal container.

    Oily rags can catch fire on their own.

Gel Stain FAQ

How long does General Finishes Gel Stain take to dry?

Allow at least 24 hours between coats. Wait 48 hours after the last coat before applying a water-based topcoat like High Performance or Gel Satin.

Do you need to sand before using gel stain?

On bare wood, sand to 180 or 220 grit. Over an existing finish, clean it thoroughly and lightly scuff-sand to dull the sheen. You don't need to strip it.

Can you put gel stain over polyurethane?

Yes. Clean and scuff-sand the polyurethane, test in a hidden area, then apply thin coats.

Why is my gel stain sticky?

Usually because too much stain was left on the surface or it hasn't dried long enough. Wipe the excess off thoroughly and give it more time in warm, dry conditions.

Is gel stain good for blotchy woods?

Yes. Because it sits near the surface, gel stain is one of the best ways to get even color on pine, maple, birch and cherry.

Shop all General Finishes Gel Stain colors and General Finishes topcoats.

Leave a comment

Please note: comments must be approved before they are published.