Question 1

whats the longest length cut I can make. In other words what is the maximum spread of the stops. View answer

Asked 5 ´years ago | MicroJIG MATCHFIT Dado Stop

Question 2

Can it cut thicker than 1/8"? View answer

Asked 6 ´years ago | MicroJIG GRR-Ripper 1/8" Thin-Stock Accessory

Question 3

Is this price for A price or single? Thank View answer

Asked 7 ´years ago

Question 4

Are the non-slip pads replaceable? View answer

Asked 6 ´years ago | MicroJIG GRR-RIP Smart Hook Push Block

Question 5

Could this jig accommodate a 28" table leg taper? View answer

Asked 5 ´years ago | MicroJIG Microdial Tapering Jig - Table Saw & Router Table

Question 6

Will the LegUp attach easily to a "Prodessional Cabinet" SawStop table saw? View answer

Asked 6 ´years ago | Infinity Tools Leg UP - Table Saw Panel Lifter

Question 7

Can the work on left and right side of the blade? View answer

Asked 6 ´years ago | INCRA Miter EXPRESS

Question 8

Would the Incra Miter V120 work with this or does one need to get another miter gage? View answer

Asked 5 ´years ago | INCRA Miter EXPRESS

Question 9

Does the Express come with a fence? If so what size? Does it come with the stop block? Thanks. View answer

Asked 5 ´years ago | INCRA Miter EXPRESS

Question 10

is there a set-up for cutting with dado blades? how? View answer

Asked 7 ´years ago | INCRA Miter EXPRESS

Question 11

Will this works with a dewalt DWE 7491 RS table saw? View answer

Asked 6 ´years ago | INCRA Miter EXPRESS

Question 12

Will this work with an Hitachi C10RA3 table saw View answer

Asked 6 ´years ago | INCRA Miter EXPRESS

Question 13

I have a small garage shop, would the INCRA Miter 5000 be a good fit on my RIDGID R4512. View answer

Asked 5 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 14

Will this work with the Rigid Model R4512 table saw? View answer

Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 15

Does this include the sled? Little confusing. View answer

Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 16

Can you use it to cut angles? View answer

Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 17

Will this work on my Delta 34-450 10" table saw? Thanks View answer

Asked 5 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 18

Do you have the right miter bar for a Shopsmith for the miter express 500 View answer

Asked 7 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 19

Can this be set up to make repeatable dado cuts? View answer

Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 20

Will it work with a dado blade? View answer

Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 21

Can this Incra miter 5000 be used as a fence for ripping boards? View answer

Asked 7 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 22

do you sell the sled table only? I already own the incra1000hd. View answer

Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 23

Can I order just a fence to upgrade my Mitre Express and Mitre Gauge V27 setup? View answer

Asked 6 ´years ago | INCRA Miter 1000HD - 180 AngleLOCK Stops

Question 24

The incra V27(is it capable of accepting the track fence at a later purchase time?) View answer

Asked 6 ´years ago | INCRA Miter V27 - with 27 AngleLOCK Stops

Question 25

WILL THE MITER GAUGE FIT ANY TABLE SAW? View answer

Asked 7 ´years ago | INCRA Miter V27 - with 27 AngleLOCK Stops

Question 26

Will is miter slide item#IMG-001 work on an Jet table saw model #JWTS-10JF View answer

Asked 6 ´years ago | INCRA Miter V27 - with 27 AngleLOCK Stops

Question 27

will miter gage fit my router T slot? View answer

Asked 6 ´years ago | INCRA Miter V27 - with 27 AngleLOCK Stops

Question 28

What is the manufacturing location of the parrot vise? View answer

Asked 11 ´months ago | Infinity Tools Parrot Vise

Question 29

Does this include one Bessey parallel clamp or a pair of them? View answer

Asked 11 ´months ago | Bessey K Body REVO Jr Parallel Jaw Clamps

Question 30

Can the Infinity 8" flat tooth saw blade fit SawStop or Dewalt saws? View answer

Asked 11 ´months ago | Infinity Tools 8" Flat-Top Dado Saw Blade, 5/8" Bore

Question 31

Does this router have a light ? View answer

Asked 1 ´year ago | Infinity Tools Router Insert Plate w/ Triton TRA001 3-1/4 HP Router

Question 32

Do you have the 15 deg shaper cutter stile and rail thats 1-1/4" bore? View answer

Asked 11 ´months ago | Infinity Tools Cabinet Door Rail & Stile Shaper Cutter Sets, 3/4" Bore

Question 33

Where are the solid carbide compression bits manufactured? View answer

Asked 1 ´year ago | Sales

Question 34

Do you have 1/4" shank router bits that make the same cuts as the two 1/2" shank bits included in the RTI-DIY kit? View answer

Asked 11 ´months ago | Paquetes de plantillas de enrutador para bricolaje de Infinity Tools

Question 35

What speed is recommended for the Infinity 17-540 1/2" shank Period Profile Bit? View answer

Asked 1 ´year ago | Infinity Tools 1/2" Shank 17th Century Router Bit, Single Ogee Bit

Question 36

Could you provide the ID and OD measurements for the 4 elbows? View answer

Asked 11 ´months ago | Infinity Tools 4" Elbow

Question 37

Is the router base plate compatible with the Rigid R24011 model? View answer

Asked 1 ´year ago | Infinity Tools Universal Circular Base Plate For Compact Routers

Question 38

Can I stack two of these for 1/2" cut? View answer

Asked 1 ´year ago | Infinity Tools 8" Flat-Top Dado Saw Blade, 5/8" Bore

Question 39

Can I get this router stand with the top and fence without the router lift? View answer

Asked 10 ´months ago | Infinity Tools Essential Router Table Package with JessEM Rout-R-Lift II (02310)

Question 40

can you add a date of birth View answer

Asked 1 ´year ago | Infinity Tools “Initials” Branding Iron

Question 41

Will bits allow wood to join at 180 deg? View answer

Asked 10 ´months ago | Infinity Tools 1/2" Shank 4-Pc. Master Lock-Miter Bit & Setup Jig Package

Question 42

How to set up locking miter bit on 3/8 wood View answer

Asked 10 ´months ago | Infinity Tools 1/2" Shank 4-Pc. Master Lock-Miter Bit & Setup Jig Package

Question 43

What is the height of your 1-3/4" OD rub collar for a 3/4" spindle shaper - SKU: RUB-100 View answer

Asked 9 ´months ago | Infinity Tools Rub Collars For Shape Up Shaper Cutters, 3/4" I.D.

Question 44

Are there accessories available, such as extensions for pepper mill drilling? View answer

Asked 9 ´months ago | Famag Bormax³ Carbide-Tipped Forstner Bits

Question 45

Does the JessEm Pow-R-Tek SR™ Router run on 220-240v? View answer

Asked 9 ´months ago | JessEm Pow-R-Tek SR™ Router with Variable Speed Control Box

Question 46

Are the Infinity Tools Inserts for the Makita LS1019L in stock? View answer

Asked 1 ´year ago | Infinity Tools 2-Pack Replacement Inserts For Makita LS1019L Miter Saw

Question 47

What is the extension length provided by the #2 Morse Taper for 10mm bits? View answer

Asked 1 ´year ago | Famag #2 Morse Taper for 10mm Hex Shank Forstner Bits

Question 48

I am looking for tints to custom color either Minwax or Duracell floor stains. Will these work? View answer

Asked 7 ´months ago | Support

Question 49

What is depth of cut? View answer

Asked 7 ´months ago | Infinity Tools V-Tongue Shaper Cutter, 3/4" Bore

Question 50

Are the profiles from the 45 degree shaper cutter and Insert-Pro Lock Miter shaper identical? View answer

Asked 1 ´year ago | Infinity Tools Insert-Pro 45° Lock Miter Shaper Cutter, 1-1/4" Bore

Browse by Topic

Tools