Question 1

So you have replacement Jaws and/or liners for this vise? Thank you! View answer

Asked 1 ´year ago | Infinity Tools Carver's & Pattern Maker's Vise

Question 2

I need to edge glue 1X6 with a 1X8 spruce, I purchased titebond III ultimate. Is that a good choice? View answer

Asked 7 ´years ago | Titebond III Ultimate Wood Glue

Question 3

Will these work for picture frame stock that is only 3/4" thick? View answer

Asked 10 ´months ago | JessEm Clear-Cut Router Table Stock Guides

Question 4

What rpm to set the router for 55-512 drawer locking bit. View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Drawer Locking Router Bit

Question 5

What is the minimum width? I'm looking for something that can deal with the undersize 1/4" plywood. View answer

Asked 7 ´years ago | Infinity Tools Dadonator Jr., 6" Stacked Dado Saw Blade Set, 5/8" Bore

Question 6

Is this food safe? View answer

Asked 10 ´months ago | General Finishes Wood Bowl Finish

Question 7

Your rail and stile router bits video shows cutting rails first, but instructions say stiles first. Which is correct? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Matched Rail & Stile Router Bits w/ Setup Block

Question 8

I'm a beginner, how do I measure the cove bit? Is there a diagram with dimensions? View answer

Asked 8 ´years ago | Infinity Tools 1/4" Shank Cove Router Bits

Question 9

What's the difference between Odie's wax and oil? Why choose one over the other for specific applications? View answer

Asked 7 ´years ago | Odie's Oil Wood Wax Food Safe Wood Finish - 9 oz. Jar

Question 10

Are the retractable rear push pads gravity dropped? View answer

Asked 5 ´months ago | BOW Products Expandable Push Shoe

Question 11

Will the Jessem Rout-R-Lift II fit a SawStop router table? The plate holes don’t seem to align for secure mounting. View answer

Asked 6 ´years ago | JessEm Rout-R-Lift II

Question 12

Will your mitre lock set up jig work with large mitre bit by CMT? View answer

Asked 6 ´years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 13

What’s the max pressure for the Venturi Vacuum System? How does it compare to PSI? Can you provide other units? View answer

Asked 6 ´years ago | Infinity Tools Venturi Vacuum System

Question 14

What is the thickness of the cast iron router table top? Will the Jessem TA router fence fit this top? View answer

Asked 7 ´years ago | Infinity Tools Cast Iron Router Table Top

Question 15

I need a crosscut sled with a pivoting miter fence for a Dewalt DWE7491RS table saw. What options do you have? View answer

Asked 7 ´years ago | INCRA Miter EXPRESS

Question 16

Approximately how long for shipping? View answer

Asked 14 ´days ago | Infinity Tools Mini Power Feeder For Router Table & Shapers

Question 17

What’s the recommended speed and feed for the 58-001 v-groove bit on a CNC router? Need RPM, depth, and feed rate. View answer

Asked 7 ´years ago | Infinity Tools 1/4" Shank Engraving V-Groove C.N.C. Router Bits

Question 18

do you have vido or print instruction help? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Bird's Mouth Router Bits

Question 19

Do you have bushings to 3/4" spindle View answer

Asked 7 ´years ago | Infinity Tools Insert-Pro Raised Panel Shaper Cutters, 1-1/4" Bore

Question 20

Can the cast iron top table be purchased without the lift, router or fence? View answer

Asked 1 ´year ago | Infinity Tools Pro Router Table Package with Triton 3-1/4 HP Router (TRA001) & Cast Iron Top

Question 21

How does Odie's work with epoxy when used to fill knots and cracks? View answer

Asked 8 ´years ago | Odie's Oil Food Safe Wood Finish - 9 oz. Jar

Question 22

Will this jig fit my Bosch TS 3000 table saw? Is the 1/4” flattop blade for 1/4” box joint dados? View answer

Asked 7 ´years ago | Infinity Tools Box Joint Jig Package with 1/4" Kerf Flat Top Blade and Setup Block Kit

Question 23

Will this fit a Laguna F2 tablesaw? View answer

Asked 3 ´months ago | Infinity Tools Tablesaw Router Table w/ Stand Only

Question 24

What tools are available to cut 5/16" wide slots 1/2" deep? Is there a single head with a 1/4" shank bit? View answer

Asked 8 ´years ago | Infinity Tools 3-Wing Slot Cutter, 5/16" I.D. x 1-7/8" O.D.

Question 25

For your collet extreme extension what height is added. View answer

Asked 7 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 26

Should I use the extended tendon shaper cutter or regular with dominoes for doors? I'm using a Domino 700 for tenons. View answer

Asked 6 ´years ago | Infinity Tools Insert-Pro Interior Door Making Shaper Cutter System, 1-1/4" Bore

Question 27

can it be used with a router table? View answer

Asked 5 ´months ago | BOW Products Expandable Push Shoe

Question 28

Do you have a setup jig for the Whiteside #3360 Lock Miter Bit, which cuts material from 1/2” to 1 1/4”? View answer

Asked 7 ´years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 29

Hi - Will JessEm Rout-R-Lift II fit in Kreg PRS2100? Thanks View answer

Asked 7 ´years ago | JessEm Rout-R-Lift II

Question 30

Will any of them fit a Delta 36-725T2? View answer

Asked 6 ´months ago | Betterly Tru-Cut Zero Clearance Tablesaw Insert System

Question 31

Is it shipped in kiazan foam? View answer

Asked 8 ´days ago | Infinity Tools 4-Pc. Corner Radius Guide Set

Question 32

For the Venturi vacuum switch: Does the compressor need to keep running after the bag is compressed? View answer

Asked 6 ´years ago | Infinity Tools Venturi Vacuum System

Question 33

Can this Bow expandable work with my JessEm Clear-cut Stock Guides on the table saw? View answer

Asked 5 ´months ago | BOW Products Expandable Push Shoe

Question 34

Will these Jessem clear cut stock guides work on the Woodpecker router table fence system? View answer

Asked 8 ´years ago | JessEm Clear-Cut Router Table Stock Guides

Question 35

What are the dimensions of the Infinity Tools Christmas Tree Tray template? View answer

Asked 1 ´year ago | Infinity Tools Christmas Tree Tray Template

Question 36

Infinity Cutting Tools Lock Miter Master Jig, (Both) View answer

Asked 1 ´year ago | Infinity Tools Lock Miter Master Jigs

Question 37

What is the diameter of the motor View answer

Asked 2 ´years ago | Triton 3-1/4 HP Dual Mode Precision Plunge Router (TRA001)

Question 38

This may have been asked already but I wanted to know if your router bits are made in the USA? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank 2-Pc. V-Tongue & Groove Router Bit Set

Question 39

Will the D Handle universal pre-drilled base plate accept a Milwaukee 2730-20 compact router? View answer

Asked 1 ´month ago | Infinity Tools Universal D-Handle Router Base Plate For Compact Routers

Question 40

does this jig accomodate a 1/2 inch offset? View answer

Asked 6 ´years ago | Kreg Concealed Hinge Jig

Question 41

Can the 61-507 T&G set be used with the 90-502 raised panel bit for 5.5/5.9 mm plywood by adjusting the depth? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Horizontal Raised Panel Router Bits

Question 42

What are the diameters of the Narex Hand Stitched rotary rasps? Need one for smoothing small scroll saw cuts. View answer

Asked 6 ´years ago | Narex Hand Stitched Rotary Rasp

Question 43

Does the Sawstop jobsite saw fence lock tight enough for these guides to work? View answer

Asked 6 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 44

Hambone View answer

Asked 2 ´years ago | Infinity Tools Router Table Top Stainless Steel Insert Ring

Question 45

Can the Triton TRA001 router be used with a Jessem Mast-R-Lift II right out of the box? View answer

Asked 6 ´years ago | Triton 3-1/4 HP Dual Mode Precision Plunge Router (TRA001)

Question 46

Is your DMG-800 dado gauge durable? The video shows wear. How thick is it, and does it flex easily? View answer

Asked 8 ´years ago | Infinity Tools Dado Measuring Gauge, 5/8" Bore

Question 47

Hi - In which country are these planes made? View answer

Asked 7 ´years ago | Infinity Tools Wood Jointer Hand Plane

Question 48

Does the 10” profile gauge have a locking function to hold patterns after moving the tool? View answer

Asked 8 ´years ago | Infinity Tools 10" Telescopic Profile Gauge

Question 49

Do you have a quick change Chuck for a Porter cable 8529 and a Hitachi M 12 V View answer

Asked 6 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 50

I have freud ec-034 shaper cutter, what jig do I need for setup View answer

Asked 7 ´years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Browse by Topic

Tools