Question 1

Is there a replacement part for the thin rip miter slot guide? View answer

Asked 6 ´years ago | Infinity Tools Thin-Rip Guide For Table Saw, Bandsaw & Router Table

Question 2

What is the size of the track that attaches to the fence? View answer

Asked 7 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 3

Do you have to replace your table saw measurement tape since your fence is now thicker? View answer

Asked 8 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 4

What is the maximum height of a fence that these guides can be mounted to, and still function properly? View answer

Asked 6 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 5

Will the clear cut table saw stock guides [ ts ] fit a desalt tablesaw [ dwe7491RS ] ? View answer

Asked 7 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 6

Is there 1 or 2 guides per order? View answer

Asked 6 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 7

I have a Ridgid ts3660 with a 2" wide fence. Will the JessEm Clear-Cut Tablesaw Stock Guides work with this fence? View answer

Asked 7 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 8

Will the JessEm stock guide fit on a DeWalt 749 contractor saw? View answer

Asked 8 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 9

I've misplaced the mounting bar and screws for the guides I ordered. can I order the replacement parts? View answer

Asked 7 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 10

Will the stock guides for the table saw fit a Bosch 4100-09? View answer

Asked 7 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 11

Will these work on a portable table saw. View answer

Asked 6 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 12

Will this work with a Sawstop Jobsite saw fence? View answer

Asked 7 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 13

Will these saw stock guides work on an Incra table saw LS system? View answer

Asked 6 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 14

I use the Incra TS-LS fence system. Will this product work with that fence? View answer

Asked 7 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 15

Do these fit the Sawstop View answer

Asked 6 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 16

I assume this will work on a biesmeyer fence. View answer

Asked 7 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 17

Will this fit on a Delta 36-L536? View answer

Asked 7 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 18

Can this be set up to make repeatable dado cuts? View answer

Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 19

Do you have the right miter bar for a Shopsmith for the miter express 500 View answer

Asked 7 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 20

Will this work on my Delta 34-450 10" table saw? Thanks View answer

Asked 5 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 21

Can you use it to cut angles? View answer

Asked 7 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 22

Does this include the sled? Little confusing. View answer

Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 23

Will this work with the Rigid Model R4512 table saw? View answer

Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 24

I have a small garage shop, would the INCRA Miter 5000 be a good fit on my RIDGID R4512. View answer

Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 25

Will this work with an Hitachi C10RA3 table saw View answer

Asked 6 ´years ago | INCRA Miter EXPRESS

Question 26

is there a set-up for cutting with dado blades? how? View answer

Asked 7 ´years ago | INCRA Miter EXPRESS

Question 27

Does the Express come with a fence? If so what size? Does it come with the stop block? Thanks. View answer

Asked 6 ´years ago | INCRA Miter EXPRESS

Question 28

Would the Incra Miter V120 work with this or does one need to get another miter gage? View answer

Asked 6 ´years ago | INCRA Miter EXPRESS

Question 29

What's in the box for $169.90? I.E. Does it come with the work piece hold down clamp? View answer

Asked 6 ´years ago | INCRA Miter EXPRESS

Question 30

Can the work on left and right side of the blade? View answer

Asked 7 ´years ago | INCRA Miter EXPRESS

Question 31

Will the LegUp attach easily to a "Prodessional Cabinet" SawStop table saw? View answer

Asked 6 ´years ago | Infinity Tools Leg UP - Table Saw Panel Lifter

Question 32

Could this jig accommodate a 28" table leg taper? View answer

Asked 6 ´years ago | MicroJIG Microdial Tapering Jig - Table Saw & Router Table

Question 33

Are the non-slip pads replaceable? View answer

Asked 7 ´years ago | MicroJIG GRR-RIP Smart Hook Push Block

Question 34

Can it cut thicker than 1/8"? View answer

Asked 6 ´years ago | MicroJIG GRR-Ripper 1/8" Thin-Stock Accessory

Question 35

whats the longest length cut I can make. In other words what is the maximum spread of the stops. View answer

Asked 6 ´years ago | MicroJIG MATCHFIT Dado Stop

Question 36

If you have the Micro Jig complete, do you need the deflector or the second handle? View answer

Asked 8 ´years ago | MicroJIG GRR-Ripper Complete Package

Question 37

will the eliminator chuck fit my Freud FT2000E router? View answer

Asked 5 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 38

Do you have a quick change Chuck for a Porter cable 8529 and a Hitachi M 12 V View answer

Asked 5 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 39

Do you have a quick change router chuck for the triton router? View answer

Asked 6 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 40

Will any of the Quick Change Chucks fit a Craftsman table router? I have model 320.37595 View answer

Asked 7 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 41

do you have a quick change chuck for Hitachi M12V? View answer

Asked 6 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 42

For your collet extreme extension what height is added. View answer

Asked 6 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 43

is there an eliminator chuck that could fit a Craftsman 315 17581? View answer

Asked 6 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 44

Does the Eliminator make this chuck for Makita rp1800 routers View answer

Asked 7 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 45

Do you have a router chuck and collar for a Craftsman model 2767 that fits 1/2? and 1/4? bits? View answer

Asked 6 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 46

will the 1/2" Eliminator Quick Change Router Chucks fit on a ryobi re600? View answer

Asked 6 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 47

Is there an Eliminator Quick Change Router Chuck for my SEARS Craftsman Router (Model 315.27500, 1/2? Collet)? View answer

Asked 7 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 48

do you have a quick change collet for a dewalt 611 router? View answer

Asked 5 ´years ago

Question 49

Quick change Router chuck for a Freud FT2000E Router what one would I buy View answer

Asked 6 ´years ago

Question 50

I have a Milwaukee 5625/ 3 1/4 inch diameter router. Which QC chuck will fit this? View answer

Asked 7 ´years ago

Browse by Topic

Tools