Question 1

My iGaging Angle Cube only reads zero. Is there a reset needed to fix this issue? View answer

Asked 7 ´years ago | iGaging Angle Cube Digital Angle Guide

Question 2

My DigiAlign miter slot runner pops up as I slide it. Adjusting the bearings didn?t help. Any advice on fixing this issue? View answer

Asked 7 ´years ago | iGaging DigiAlign With Track

Question 3

Can the gage be turned upside down on the slide to measure height above the bed of a 6" planer to set rollers? View answer

Asked 6 ´years ago | iGaging 6" Digital Height Gauge

Question 4

How easy are scribes to change? What?s the cost of replacements? Are carbide inserts available for marking steel? View answer

Asked 6 ´years ago | iGaging 3-in-1 Digital Marking & Mortise Gauge

Question 5

Will this work on Supermax 19-38 drum sander? View answer

Asked 7 ´years ago | iGaging Digital Measuring Sets

Question 6

If the surface is nonmetallic, how stable is this unit when it can't use the magnetic base? View answer

Asked 8 ´years ago | iGaging Multi-Purpose Digital Snap Gauge

Question 7

Is there a fence that can be bought separately for the incra V27? View answer

Asked 6 ´years ago | Ingletadora INCRA V27 con 27 topes AngleLOCK

Question 8

does the miter gauge capture within the T at the bottom of the table slot? if so, is it adjustable for play? View answer

Asked 6 ´years ago | Ingletadora INCRA V27 con 27 topes AngleLOCK

Question 9

Will this one work in the slots on a Shopsmith? View answer

Asked 6 ´years ago | INCRA Miter 1000SE with 18" to 31" Fence & Flip Stop

Question 10

Will this work with a right-handed miter slot? My Laguna TSS saw has a 3/4" slot on the right side. View answer

Asked 6 ´years ago | INCRA Miter 1000SE with 18" to 31" Fence & Flip Stop

Question 11

Can I buy just the protractor for the Incra 1000HD miter gauge separately? Mine was damaged and needs replacement. View answer

Asked 7 ´years ago | Ingletadora INCRA 1000HD - Topes AngleLOCK de 180 grados

Question 12

Can a sacrificial board prevent chip-out on picture frame miters? Will the fence stops still work? View answer

Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 13

Is just the sled available for sale because I already own the miter gauge that I purchased a while back? View answer

Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 14

Will this fit my contractors SawStop? Do I need to calibrate the back fence for a perfect 90 degrees? View answer

Asked 7 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 15

What are the overall size, base material, thickness, and surface of the table? View answer

Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 16

Will the tool work efficiently at 6 and 10 degrees for stool leg installations, even without dedicated stops? View answer

Asked 6 ´years ago | Milescraft Drill Mate Portable Drill Guide

Question 17

My miter saw station has 8' to the left and 4' to the right. Can additional aluminum lengths be purchased? View answer

Asked 6 ´years ago | Infinity Tools 96" Professional Miter Saw Fence System

Question 18

Are the rails sized the same as any other system (Incra, JessM)? View answer

Asked 6 ´years ago | Infinity Tools 96" Professional Miter Saw Fence System

Question 19

Do the flip stops have an adjustable cursor so you can fine tune them after you install the measuring tape? View answer

Asked 6 ´years ago | Infinity Tools 96" Professional Miter Saw Fence System

Question 20

where the adhesive tape is glued to the aluminum profile? View answer

Asked 6 ´years ago | Infinity Tools 96" Professional Miter Saw Fence System

Question 21

How does your Miter Saw Fence system slide for compound miters if installed close to the sliding chop saw fence? View answer

Asked 6 ´years ago | Infinity Tools 96" Professional Miter Saw Fence System

Question 22

What are the flip stops of the miter saw fence made of? View answer

Asked 6 ´years ago | Infinity Tools 96" Professional Miter Saw Fence System

Question 23

Will flip stops (FSS-349) fit Incremental Tools top rail? What’s the height of the miter saw fence (100-349)? View answer

Asked 6 ´years ago | Infinity Tools 96" Professional Miter Saw Fence System

Question 24

Will your fence work on a Porter Cable 12” miter saw if the right section is bent and I can’t find a replacement? View answer

Asked 6 ´years ago | Infinity Tools 96" Professional Miter Saw Fence System

Question 25

How thick are your adhesive measuring tapes and what material? Do you sell extra mounting hardware? View answer

Asked 6 ´years ago | Infinity Tools 96" Professional Miter Saw Fence System

Question 26

Do you sell the attachment set (stops, tape) without rails? Interested in using Woodpecker rails and additional stops. View answer

Asked 6 ´years ago | Infinity Tools 96" Professional Miter Saw Fence System

Question 27

Can I get a shorter miter saw fence rail than 4'? My saw's right side can't fit a 4' rail. View answer

Asked 6 ´years ago | Infinity Tools 96" Professional Miter Saw Fence System

Question 28

The TSRT-029 router fence mount tracks don’t fit my Rigid table saw's miter tracks. What should I use instead of t-bolts for mounting? View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 29

Can you make a router table top to match Indra dimensions with BB ply? Or can I buy a blank top with an aluminum insert cutout? View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 30

Does the TSRT-029 miter track clear the fence rail on a SawStop 36” PCS, like the TSRT-047 on a 52” PCS? View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 31

Will the Woodpecker Superfence work with this table? View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 32

Will your router table product fit a Grizzly G0690 saw and a Jesse MastR List II router plate? View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 33

Will TSRT 29 table fit a Rockler Pro Lift without modification? Is it stable with an Incra TS LS fence system? View answer

Asked 5 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 34

Will my DeWalt 745 portable table saw work with the TSRT-029? View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 35

Will this work with a Ridgid Table Saw Model #4513? View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 36

Can the 27 x 47 table saw router table top be configured to run alongtheu 47 inch side View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 37

Does TSRT-029 include the router plate, router, and table fence? What else might I need for my Porter Cable PCB270TS saw? View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 38

Will your RTT-029 table fit my Grizzly G1023RLW without modification? Will the 3” overhang cause issues with my setup? View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 39

Does the RTT-047 table accept the Jessem Rout-R-Lift? Can the Woodpeckers Superfence be used with it? View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 40

Can I use just a regular portable table saw for this table or does it have to be a cabinet saw? View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 41

I want a router table but have my own router. What should I buy and how much would it cost without the router? View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 42

Will the 9 1/4" x 11 3/4" Woodpecker router plate fit in the Table Saw Router Table (27" x 47") top? View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 43

Could you tell me the dimensions of this table? I don't have a lot of room in my shop so size is an issue. View answer

Asked 6 ´years ago | Table Saw Out-feed Table

Question 44

Where did you buy the table top? View answer

Asked 7 ´years ago | Table Saw Out-feed Table

Question 45

I have PROJECT-006 and PROJECT-007. Can you provide material and cut lists? I need help as I’m not great with schematics. View answer

Asked 6 ´years ago | Table Saw Out-feed Table

Question 46

Does the handle control both clamping and swiveling, or is there a separate mechanism to lock/release the swivel? View answer

Asked 6 ´years ago | Infinity Tools Carver's Vise

Question 47

What are the vise dimensions? How far do the jaws open and what width are they? Is this a standard luthier’s vise? View answer

Asked 6 ´years ago | Infinity Tools Carver's Vise

Question 48

Can this mini feeder be used on a jointer View answer

Asked 6 ´years ago | Infinity Tools Mini Power Feeder For Router Table & Shapers

Question 49

What size hole to you make for the threaded inserts for the MPF-001? View answer

Asked 6 ´years ago | Infinity Tools Mini Power Feeder For Router Table & Shapers

Question 50

will the mini power feeder fit on my laguna lt 16 hd bandsaw ? View answer

Asked 6 ´years ago | Infinity Tools Mini Power Feeder For Router Table & Shapers

Browse by Topic

Tools