Question 1

Does this work on carbide blades? View answer

Asked 7 ´years ago | Deulen 6" Jointer Knife Sharpener - For Knives Up To 8" Long

Question 2

will this work with Dewalt 735 knives? View answer

Asked 7 ´years ago | Deulen 6" Jointer Knife Sharpener - For Knives Up To 8" Long

Question 3

do you have cursive letters and numbers that will fit our is there a way to make templets View answer

Asked 6 ´years ago | Milescraft SignPro Kit

Question 4

What is the shank size of router bits? Can I get 1/4 inch bits? View answer

Asked 7 ´years ago | Milescraft SignPro Kit

Question 5

Will base plate fit on a De Walt router? View answer

Asked 7 ´years ago | Milescraft SignPro Kit

Question 6

Will this work in a vertical plane or only horizontal? View answer

Asked 7 ´years ago | Milescraft SignPro Kit

Question 7

Will this work using the smaller Dewalt 611 router? View answer

Asked 7 ´years ago | Milescraft Router Circle Guide Kit

Question 8

Can triple bead and triple flute bits be used with a plunge router? I want to use them on a large butcher block edge. View answer

Asked 5 ´years ago | Infinity Tools 1/2" Shank Triple Flute & Bead Router Bits

Question 9

Does the junior set require a 1/4" thick tenon like the larger bit set? The stock thickness wasn't mentioned. View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Window Sash Router Bit Sets

Question 10

My stock thickness for window sashes is 1 3/4". What sash router bit would you recommend? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Window Sash Router Bit Sets

Question 11

Looking for a larger bit set for 2 thick window sash with 1 profile. Do you have a suitable set for this job? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Window Sash Router Bit Sets

Question 12

How does the bearing option affect the 59-501? I need it for a full-depth window stool profile on 5/4 stock. View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Window Sill Router Bits

Question 13

Will this table fit a Jet 12" bench top drill press? View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 14

Will the DPT200 fit a Jet JDP20MF drill press with an 18” x 16” top, #6T slots 1/2” wide and centered at 3-1/2”? View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 15

will this fit on a old craftsman bench top drill press with a round table. View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 16

Will your drill press table install on my JET DPW-17 floor-standing drill press with an 11.5 inch round table? View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 17

What hardware secures the table to the drill press? Is the mounting hardware recessed and adjustable to align with existing slots? View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 18

Will the Shop Fox W1668 drill press’s table elevation crank arm clear the table? Any modifications needed? View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 19

What is the distance between the two outer T tracks ? Will 5/16 T bolts fit in the t tracks on your table? View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 20

What is the price for the table alone? I already have a fence, but the table is superior to the one I have. View answer

Asked 7 ´years ago | Infinity Tools Drill Press Table Packages

Question 21

How do I know if my drill press is 10"of 12'' or what ever? How are they measured? View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 22

Do you offer a fence stop that fits the top/side t-slots of a fence, similar to the Biesemeyer 18-901? I’m looking for options for repeatable work. View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 23

Are there aftermarket flip stops that fit my fence perfectly and extend the entire length? I want something precise and durable. View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 24

Can I use the Rockler drill press fence with your table? Will the Rockler t bolts fit in your tracks? View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 25

My drill press has a round table. Will your table fit it ? View answer

Asked 7 ´years ago | Infinity Tools Drill Press Table Packages

Question 26

Why can't I use the table on a 10 inch bench top drill press? View answer

Asked 7 ´years ago | Infinity Tools Drill Press Table Packages

Question 27

Will this work with my 8" Harbor Freight Table Top Drill Press View answer

Asked 7 ´years ago | Infinity Tools Drill Press Table Packages

Question 28

Do you have guides for a blind person to cut plywood full length? My brother has a woodworking shop in his garage. View answer

Asked 7 ´years ago | Kreg Accu-Cut and Rip-Cut Systems (KMA2685 & KMA2700)

Question 29

Is using foam backer board for cutting effective, or is it just for display? Could it be costly for frequent cuts? View answer

Asked 8 ´years ago | Kreg Accu-Cut and Rip-Cut Systems (KMA2685 & KMA2700)

Question 30

How do the blades in the essential package compare to a woodworker II blade? View answer

Asked 7 ´years ago | Infinity 2-Pc. 8" Dadonator & Full Kerf Super General Saw Blade Package, 5/8" Bore

Question 31

I need a 10" Fine Crosscutting Saw Blade for my mitre saw but my Bosch table saw needs an 8" blade. Do you have one? View answer

Asked 6 ´years ago | Infinity Tools 10" x 50T Combination Tablesaw Blades, 5/8" Bore

Question 32

Does this cut a flat bottom cut or is it a v-cut? I am looking for something to use to cut quick rabbets View answer

Asked 7 ´years ago | Infinity Tools 10" x 50T Combination Tablesaw Blades, 5/8" Bore

Question 33

I received a spline making sled but the nuts are misaligned (2 3/8" & 2 1/4"). Please send a replacement. View answer

Asked 6 ´years ago | Infinity Tools Master Tapered Dovetail Spline System w/ Router Jigs, Spline Making Sled, 6 Dovetail Bits & 2 Brass Guides

Question 34

To make nested dovetails as shown in your video, what should I order? Are there other patterns available? View answer

Asked 7 ´years ago | Infinity Tools Master Tapered Dovetail Spline System w/ Router Jigs, Spline Making Sled, 6 Dovetail Bits & 2 Brass Guides

Question 35

how do I add this item to my wish list? View answer

Asked 7 ´years ago | Infinity Tools Master Tapered Dovetail Spline System w/ Router Jigs, Spline Making Sled, 6 Dovetail Bits & 2 Brass Guides

Question 36

Are the slots in the 18? jig the same as the 12? jig? Can the 1/2? x 14¯ bit work with the 18? jig? View answer

Asked 6 ´years ago | Infinity Tools Master Tapered Dovetail Spline System w/ Router Jigs, Spline Making Sled, 6 Dovetail Bits & 2 Brass Guides

Question 37

I bought a dovetail spline system. Can I buy separate sled rails for 14 and 18-degree bits? View answer

Asked 7 ´years ago | Infinity Tools Master Tapered Dovetail Spline System w/ Router Jigs, Spline Making Sled, 6 Dovetail Bits & 2 Brass Guides

Question 38

Will your Rail & Stile bit set #00-525 work for a 5-panel door with 4 windows in the top panels? View answer

Asked 6 ´years ago | Infinity Tools Divided Light Door Kit For Rail & Stile Router Bit Sets

Question 39

Can I use item 23-GLS with item 00-102 to build a cabinet door with glass that has a curved top rail? View answer

Asked 7 ´years ago | Infinity Tools Divided Light Door Kit For Rail & Stile Router Bit Sets

Question 40

Any issues with Infinity bits? My previous ones from another manufacturer were poorly made. View answer

Asked 7 ´years ago | Infinity Tools 1/4" Shank Brass Guided Chamfer Router Bits

Question 41

Does the Brass Pilot Router Bit spin like a bearing? I want to avoid marks or grooves. View answer

Asked 7 ´years ago | Infinity Tools 1/4" Shank Brass Guided Chamfer Router Bits

Question 42

Why did the 54-525 bullnose bit chip my red oak board? It was in the middle, not the end. How can I avoid this in my stair treads? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Bullnose Router Bits

Question 43

I?m replacing a window stool in a 1900 schoolhouse. Will the 54-504 bit give a full bullnose on 1 1/8? material? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Bullnose Router Bits

Question 44

For full bullnose on 1-1/32 thick oak stair treads, should I use a 1-1/8 bullnose bit or a 3/4 round over bit? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Bullnose Router Bits

Question 45

What are the safe RPM speeds for raised panel and stile/rail insert pro cutters on my shaper? View answer

Asked 7 ´years ago | Infinity Tools Raised Panel Insert-Pro Shaper Cutters, 1-1/4" Bore

Question 46

Does the shaper bit have a 1/2" shank for use in router tables or just shapers? View answer

Asked 6 ´years ago | Infinity Tools Raised Panel Insert-Pro Shaper Cutters, 1-1/4" Bore

Question 47

Are your Infinity Rip Bandsaw Blades suitable for resawing hardwoods like ebony or cocobolo? View answer

Asked 7 ´years ago | Infinity Tools Resaw Bandsaw Blades

Question 48

I have a Laguna 18" bandsaw that requires a blade 145" long. Do you sell non-stock lengths for bandsaw blades? View answer

Asked 6 ´years ago | Infinity Tools Resaw Bandsaw Blades

Question 49

Can the 90-509 bit be used without the back cutter blade, or do I need an additional cove bit? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Raised Panel Router Bits w/ Backcutter

Question 50

Why doesn’t the RCH-006 rosette cutter picture match the actual rosette? I want the cutter that matches the RCH-006 image. View answer

Asked 6 ´years ago | Infinity Tools Carbide Tipped Rosette Cutters, 2-1/8" Diameter

Browse by Topic

Tools