Infinity Cutting Tools Q&A
Do you provide CNC info for router bits, like recommended feed rates or spindle speeds? View answer
Asked 8 ´years ago | Infinity Tools 1/4" Shank Roundnose Router Bits
Do you have a round nose corebox bit for a circular concave hollow between 1.5 and 2 inches diameter, 0.5 to 0.7 inches deep? Is there an Australian dealer? View answer
Asked 7 ´years ago | Infinity Tools 1/4" Shank Roundnose Router Bits
For porch trim on a historic home, I need a bit with a 1/8” reveal on both sides of the bead. Can the 38-880 bit be adjusted with a 1/4” bearing? View answer
Asked 6 ´years ago | Infinity Tools 1/4" Shank Roundover & Beading Router Bits
I need to replace old window trim (2.75 x 0.75 fluted edges). Can you suggest a router bit or alternative? View answer
Asked 7 ´years ago | Infinity Tools 1/4" Shank Roundover & Beading Router Bits
Can the 83-140 Flute cutter be used with the 83-130 Bull Nose cutter like the 55-701 router flute and bead set? View answer
Asked 5 ´years ago | Infinity Tools Single Flute Shape Up Shaper Cutters, 3/4" Bore
Please indicate the proper stacking of the cutter, bearing, and washers for me! View answer
Asked 7 ´years ago | Infinity Tools Slot Cutter w/ 1/4" Shank Arbor
I need a 1/4 shank tongue and groove cutter for plywood slightly under 1/4". Can you provide the part number and delivery to Canada? View answer
For cutting 3/16" high and deep slots, is the 23-316B Slot Cutter suitable? What bearing should I use for this purpose? View answer
Asked 6 ´years ago | Infinity Tools Slot Cutter w/ 1/4" Shank Arbor
Do you have a slot cutter that cuts a 1/16 inch wide slot? View answer
Asked 8 ´years ago | Infinity Tools Slot Cutter w/ 1/4" Shank Arbor
Looking for a slot cutter router bit with a 1/4” arbor that cuts 1/4” high and 1/4” deep. Do you have this? View answer
What tools are available to cut 5/16" wide slots 1/2" deep? Is there a single head with a 1/4" shank bit? View answer
Asked 8 ´years ago | Infinity Tools 3-Wing Slot Cutter, 5/16" I.D. x 1-7/8" O.D.
How do your bits perform with 0.060" aluminum? We are looking for 1/2" shank 1/2" cutter with a 5/8" bearing View answer
Asked 7 ´years ago | Infinity Tools 1/4" Shank x 1/4" Cutter Diameter x 1" Cutter Length. Solid Carbide Spiral Flush Trim Router Bits
I have the 06-694 pattern mega-bit and need to pattern cut two 5/4 hard maple pieces. Will the 2" bit accommodate this thickness? View answer
Looking for a flush trim router bit with a middle-bearing to trim top and bottom laminate in one pass. Exists? View answer
Is there a pattern bit with a 3/8" or smaller diameter cutter head and guide bearing on top? The 85-120 doesn’t fit my needs. View answer
Can spiral flush trim bits be sharpened ? For that matter, can any bearing pilot, flush trim bit be sharpened? View answer
What speed do you recommend for an upcut sprial bit? View answer
Asked 8 ´years ago | Infinity Tools 1/4" Shank Solid Carbide Spiral Upcut Router Bits
I need a router bit for 2.5” deep mortises in hard maple. Any recommendations for making flat-bottomed mortises? View answer
Asked 7 ´years ago | Infinity Tools 1/4" Shank Solid Carbide Spiral Upcut Router Bits
Which bit is best for cutting a 2 3/4” thick hardwood table top with a plunge router? Thanks! View answer
Asked 6 ´years ago | Infinity Tools 1/4" Shank Solid Carbide Spiral Upcut Router Bits
Looking for a 1/4” shank down cut set for dados in 1/4, 3/8, 1/2, and 3/4” plywood. Is the 1/4” shank available? View answer
I am looking for a straight bit .6 inch diameter with 1/4 shank View answer
Asked 6 ´years ago | Infinity Tools 1/4" Shank Straight Router Bits w/ Plunge Point
Does your sanding disc have a 2-degree taper for inline sanding? I couldn’t find this feature listed. View answer
Asked 6 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'
Does the hook and loop disk come attached to the metal disc? What is the finest grit available? View answer
Should I adjust the RPMs on my table saw to use a sanding disk? Any advice on speed adjusters? View answer
Do you sell the 00-SSD Table Saw Setup & Sanding Disk Premium Package in Australia? View answer
Asked 5 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'
Are the sanding disks aluminum oxide? Do you sell a gizmo for fine-tuning a table saw using a caliper? View answer
Asked 7 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'
Wll this "Table Saw Setup & Sanding Disk Premium Package", work with my 10" SawStop Professional 3.0 hp.? View answer
Asked 8 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'
Is your 10" table saw sanding disc compatible with a SawStop table saw? View answer
Will the 61-511 work for wood less than 3/4" thick? I'm planning to mill old pine trim for flooring. View answer
Asked 6 ´years ago | Infinity Tools 1/2" Shank Floor Making Router Bit Sets
This may have been asked already but I wanted to know if your router bits are made in the USA? View answer
I need to cut tongue and groove on maple flooring but can't get the router bit low enough. Any solutions? View answer
Does the 61-511 bit set create 1/4” tongue/grooves? I need to match old flooring and the site doesn’t specify bit sizes. View answer
How many linear feet will the 61-511 Tongue and Groove Flooring Bit Set cut before needing sharpening? Do you have a bit for 1" stock with a nail slot? View answer
What is the shaft length for 12-327B and 11-790B? I am looking for at least a shaft length of 1.5 inches. View answer
Asked 6 ´years ago | Infinity Tools 1/4" Shank Straight Router Bit w/ Top Bearing
Does your company still make the Jesada 612-690 1/2" shank top bearing pattern bit, or is there a replacement? View answer
I need a bit for a 78 radius curve on a 3 thick maple top. What bit should I use with a plywood pattern? View answer
Does Mike Pekovich use your top bearing pattern bit with his router dovetailing jig? Which specific bit? View answer
I have a Shopsmith Mark 7 and need the sled only. Will it work with the Shopsmith, and can I get an extender? View answer
Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled
Will this work with the jobsite tablesaw Dewalt 7941RS? View answer
Asked 7 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled
Will this work with a SkilSaw 10 inch model SPT70WT-22? View answer
Will this fit a Bosch 4100 10? portable table saw? The Incra specs seem to suggest compatibility. View answer
Wondering what saws this fits? I have a dewalt table saw View answer
Does this sled come with the miter guage? View answer
Can the right side of the Miter Express sled accommodate a dado stack with my Incra Miter Gauge 1000? View answer
Asked 6 ´years ago | INCRA Miter EXPRESS
Will the Incra crosscut sled work with a SawStop? Is it adjustable enough? View answer
Asked 7 ´years ago | INCRA Miter EXPRESS
Preciso de um acess¢rio completo de seguranáa para serra de mesa. Vocàs vendem as peáas individuais? Aguardo resposta. View answer
Asked 7 ´years ago | MicroJIG GRR-Ripper Handle Bridge Kit
Can not find the video on the microfit jig use I already have one need to refresh how to use itv View answer
Asked 7 ´years ago | MicroJIG MATCHFIT Dado Stop
How can I tell if your sizes fit the collet threading on my Grizzly shaper? View answer
Asked 7 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks
I need directions for my Porter Cable 7518 quick change chuck. The bit is hard to tighten/loosen. Any cleaning or maintenance tips? View answer
Will the router collet xtreme extension fit a Harbor Freight router table? Which model should I order? View answer
Asked 6 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks
Infinity Cutting Tools Q&A
