Question 1

Hi I have an older Bosch plunge 3.25 hp 1615 EVS router, is my router compatible with the RTF-007? View answer

Asked 6 ´years ago | JessEm Rout-R-Lift Prestige for Plunge Based Routers

Question 2

What are the 2 yellow strips on the phenolic and what's their purpose? View answer

Asked 6 ´years ago | Infinity Tools HD Frame Master - For HD Frame Templates - Router Or Shaper

Question 3

Do you have a 30° Lock Miter Router Bit Set for a 6-sided project or another suitable router bit? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank 22.5° Lock Miter Router Bit Set w/ Setup Block

Question 4

What exactly does this mean--Requires minimum 2.5 CFM @ 90 PSI View answer

Asked 6 ´years ago | Venturi Vacuum System

Question 5

Do you sell the Leigh 5/16 straight bit for D4Pro jig without the whole set? View answer

Asked 6 ´years ago | Infinity Tools 1/4" Shank Dovetail Router Bits

Question 6

Do you carry any 96" bandsaw blades? If so, what widths and TPI View answer

Asked 6 ´years ago | Infinity Tools Resaw Bandsaw Blades

Question 7

Do the plugfones come with a guarantee? View answer

Asked 6 ´years ago | Plugfones - Liberate 2.0 Bluetooth Earplug Headphones

Question 8

is there a list or routers which this fits - specifically does it fit a Porter Cable 690 series View answer

Asked 6 ´years ago | MPOWER 3-Pc. CRB7 Router Base Complete Package

Question 9

for the 12" x 12" predrilled router base plate what is the thickness 1/4" or 3/8" View answer

Asked 6 ´years ago | Infinity Tools Universal 7.5" Router Base Plate

Question 10

Which bit would work better with 3/4 stock the sr. or jr. View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Lock Miter Jr. Router Bit

Question 11

need speed control for my Titon TRA001 31/4 Router. Speed control # TRA027. Where or how can I get it. View answer

Asked 6 ´years ago | Triton 3-1/4 HP Dual Mode Precision Plunge Router (TRA001)

Question 12

Will the clear cut table saw stock guides [ ts ] fit a desalt tablesaw [ dwe7491RS ] ? View answer

Asked 6 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 13

What is the distance from the jig’s front edge to the miter bar? Min. and max. distance from miter channel to bit center? View answer

Asked 6 ´years ago | Infinity Tools Vertical Router Sled

Question 14

I can't tell from the pictures. Is the sole square to the side thereby allowing use in a shooting board? View answer

Asked 6 ´years ago | Infinity Tools Wood Jack Hand Plane

Question 15

how do I add this item to my wish list? View answer

Asked 6 ´years ago | Infinity Tools Master Tapered Dovetail Spline System w/ Router Jigs, Spline Making Sled, 6 Dovetail Bits & 2 Brass Guides

Question 16

Is there a special clamp for attaching the guide to the underside of the workpiece? View answer

Asked 6 ´years ago | Kreg Accu-Cut and Rip-Cut Systems (KMA2685 & KMA2700)

Question 17

To make nested dovetails as shown in your video, what should I order? Are there other patterns available? View answer

Asked 6 ´years ago | Infinity Tools Master Tapered Dovetail Spline System w/ Router Jigs, Spline Making Sled, 6 Dovetail Bits & 2 Brass Guides

Question 18

I'm interested in Item Number: 100-700C, can you change the font? View answer

Asked 6 ´years ago

Question 19

Can this be put on a table saw View answer

Asked 6 ´years ago | Infinity Tools 10" x 50T Combination Tablesaw Blades, 5/8" Bore

Question 20

Does the JessEm 10 pc lock ring set fit the Kreg router table? View answer

Asked 6 ´years ago | Infinity Tools Aluminum Router Table Insert Plate, 9-1/4" x 11-3/4"

Question 21

For item 00-201, what is the diagonal width of the raised panel when installed in stile or rail? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank 3-Pc. Cabinetmaker's Combo Router Bit Set w/ Backcutter

Question 22

I have a Ridgid 4512 Cast iron table saw, which insert fits this model? View answer

Asked 6 ´years ago | Betterley Tru-Cut Insert System For Delta Right Tilt Unisaw

Question 23

Stupid question but can these bits be used in a handheld router or just with a router and table? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Picture & Frame Making Router Bits

Question 24

I have the jointer with 6 inch 3/4 1/8 knives do you have any proposal for that? View answer

Asked 6 ´years ago | Infinity Tools High Speed Steel Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets

Question 25

What size bull nose bit do I need for 3/4 wood? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Bullnose Router Bits

Question 26

What bit can I use to round the 3/4 inch and 1 inch wood edge? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank 5-Pc. Bullnose Router Bit Set

Question 27

I have a jig for a 1/2” lumber but need it for 5/8” ply. How should I position the gauge? View answer

Asked 6 ´years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 28

I need to edge glue 1X6 with a 1X8 spruce, I purchased titebond III ultimate. Is that a good choice? View answer

Asked 6 ´years ago | Pegamento para madera Titebond III Ultimate

Question 29

For bit 90-506, what is the length of the 1/4” flat profile from inside the rail to where the bevel starts? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Horizontal Raised Panel Router Bits

Question 30

I have an Inca (Swiss made) 10-1/4" planer joiner! l would like a set of carbide knives for it! View answer

Asked 6 ´years ago | Infinity Tools Carbide Tipped Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets

Question 31

Does the 10-Pc. TAB-LOCK Ring Insert Set include an insert for Porter Cable bushings? I have a Jessem router lift. View answer

Asked 6 ´years ago | Infinity Tools Aluminum Router Table Insert Plate, 9-1/4" x 11-3/4"

Question 32

I need 12" chop saw blade that can cut 1/4 wall 4Ã—4 steal tubs View answer

Asked 6 ´years ago | Infinity Tools 12" Miter Saw Blade

Question 33

Does the LMM-002 jig work with the Jesada 655-502 lock miter bit? I’ve struggled using it properly. View answer

Asked 6 ´years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 34

Can you supply raised panel cutter, back cutter and proper rub collar without the stile & rail cutters? View answer

Asked 6 ´years ago | Infinity Tools 3-Pc. Cabinet Door Shape-Up Shaper Cutter Sets

Question 35

Is this the new CRB7MK3 kit or an older version? My Dewalt DWP611 router needs the newest CRB7 version. View answer

Asked 6 ´years ago | MPOWER 3-Pc. CRB7 Router Base Complete Package

Question 36

Can I buy the 36" fence and brackets separately for the Magswitch work holding starter kit? Do you have a taller fence? View answer

Asked 6 ´years ago | Magswitch 18" Universal T-Track Fence

Question 37

Looking for a 3” mortising bit with a 1/2” shank. Do you have wider options? Thanks, and have a great day! View answer

Asked 6 ´years ago | Infinity Tools 1/4" Shank Mortise & Tenon Router Bits

Question 38

Hi - I've set up the dovetail spline sled. Any tips on making the first cut into the sled? View answer

Asked 6 ´years ago | Infinity Tools Master Tapered Dovetail Spline System w/ Router Jigs, Spline Making Sled, 6 Dovetail Bits & 2 Brass Guides

Question 39

does it accept both 1/2'' and 1/4'' shank? View answer

Asked 6 ´years ago | Triton 3-1/4 HP Dual Mode Precision Plunge Router (TRA001)

Question 40

How do I know if my rigid table saw has the 7/16 or the 3/32 plate. View answer

Asked 6 ´years ago | Betterley Tru-Cut Insert System For Delta Right Tilt Unisaw

Question 41

Does this package come with an offset wrench for changing bits without having to lift t the router? View answer

Asked 6 ´years ago | Infinity Tools Pro Router Table Package with Triton 3-1/4 HP Router (TRA001)

Question 42

What is the weight of the Jointer Plane? View answer

Asked 6 ´years ago | Infinity Tools Wood Jointer Hand Plane

Question 43

Does the RTL-002 fit within the Rockler "œbucket boss" dust collection enclosure ? View answer

Asked 6 ´years ago | JessEm Mast-R-Lift II - 8-1/4" x 11-3/4" Aluminum Plate

Question 44

Is there a Tru-Cut Table Saw Insert System for the Dewalt DWE7491RS 10-inch jobsite table saw? View answer

Asked 6 ´years ago | Betterley Tru-Cut Insert System For Delta Right Tilt Unisaw

Question 45

Can the bit #50-002 be adjusted to cut a t-slot slightly deeper and wider on my router table? View answer

Asked 6 ´years ago | Infinity Tools T-Slot, Channel & Hinge Router Bits

Question 46

What is this made of? View answer

Asked 6 ´years ago | FastCap Miter Saw Safety Stick

Question 47

Looking for an Ogee bit similar to the 56-517 profile in the American Woodworker book. Is this one yours? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Picture & Frame Making Router Bits

Question 48

What is the internal diameter of this product? Will it fit two solid pieces with a 2.5” OD? View answer

Asked 6 ´years ago | Infinity Tools 2-1/2" Splice

Question 49

Will the 50" straight edge clamp span a 4 ft wide plywood piece, considering clamp and stop space? View answer

Asked 6 ´years ago | Infinity Tools 2" Wide Pro-Grip Straight Edge Clamps

Question 50

Will this jig fit my Bosch TS 3000 table saw? Is the 1/4” flattop blade for 1/4” box joint dados? View answer

Asked 6 ´years ago | Infinity Tools Box Joint Jig Package with 1/4" Kerf Flat Top Blade and Setup Block Kit

Browse by Topic

Tools