Question 1

The 55-512 drawer lock bit setup block shows a 1970 date. What’s the actual availability date for this item? View answer

Answer posted 6 years ago | Infinity Tools Setup Block for 55-501 Glue Joint Bit

Question 2

Do you have a UK supplier for your drill press tables? I’ve only found one that sells router bits. View answer

Answer posted 6 years ago | Guía láser de precisión para taladro de columna Wixey

Question 3

Will the Woodpeckers Deluxe Drill Press Table fit my Clarke drill press with a 12" round table and 6 radial slots? View answer

Answer posted 6 years ago | Infinity Tools Drill Press Table Package w/ Essential Aluminum Fence

Question 4

I have a 3" tall Incra fence. Do you have a solution to lower the clear acrylic guide to the correct height? View answer

Answer posted 6 years ago | Infinity Tools Pro Coping Sled

Question 5

How deep do the brass pilots go? Trying to rout a round over on some small holes that are not very deep. View answer

Answer posted 6 years ago | Infinity Tools 1/4" Shank Brass Guided Chamfer Router Bits

Question 6

Are the crown moulding router bits carbide tipped? View answer

Answer posted 6 years ago | Infinity Tools 1/2" Shank Cove Crown Molding Router Bits

Question 7

Will this lift plate fit in a Bench Dog router table? View answer

Answer posted 6 years ago | JessEm Mast-R-Lift II - 8-1/4" x 11-3/4" Aluminum Plate

Question 8

Does this guide fit a Festool OF1010, Festool MKF700, DEWALT DW621, TRITON TRA 001 1/2" ? View answer

Answer posted 6 years ago | Kit de guía circular para fresadora Milescraft

Question 9

Restoring an 1872 home, need a router bit for 1/2 thick stock with a 3/8 thick bead profile. Can you make or find this bit? View answer

Answer posted 6 years ago | Infinity Tools 1/2" Shank Classical Bead Router Bit

Question 10

For using a bit, do I need to add extra stock to the drawer's total measurement, e.g., for a 20"x12" drawer? View answer

Answer posted 6 years ago | Infinity Tools 1/2" Shank Drawer Locking Router Bit

Question 11

Can spiral flush trim bits be sharpened ? For that matter, can any bearing pilot, flush trim bit be sharpened? View answer

Answer posted 6 years ago | Infinity Tools 1/4" Shank x 1/4" Cutter Diameter x 1" Cutter Length. Solid Carbide Spiral Flush Trim Router Bits

Question 12

Which shaper cutter do I need for a bullnose on a 3/4 inch stair tread - Would it be your 83-135 cutter? View answer

Answer posted 6 years ago | Infinity Tools Bullnose Shape-Up Shaper Cutter

Question 13

What fitting is needed to attach a hose to a fixture plate for holding sheet metal flat? Can I get these fittings from you? View answer

Answer posted 6 years ago | Venturi Vacuum System

Question 14

My dust collector is 2 hp on a 30amp 230V circuit. Is the 5-piece system the right one? Don’t want to buy the wrong unit. View answer

Answer posted 6 years ago | Paquete de recolección de polvo automático iVac de 5 piezas con interruptor de 115 V CA

Question 15

will I need longer baseplate screws for the new base? or are they included? View answer

Answer posted 6 years ago | Infinity Tools Universal D-Handle Router Base Plate For Compact Routers

Question 16

will blades fit ridge saw View answer

Answer posted 6 years ago | Imperial Blades 2-1/2" Fast Wood HCS Blade - Universal Fit

Question 17

Will QCC-BOS fit my Bosch MR23EVS? View answer

Answer posted 6 years ago

Question 18

Any suggestions on how to remove the double sided tape residue glue from the templates? View answer

Answer posted 6 years ago | Infinity Tools 20-Pc. Assorted Wood Pack

Question 19

Hello. Does this fit the Bosch 1617evs 2.25hp router? Thanks. View answer

Answer posted 6 years ago | Infinity Tools Router Bit Collet Extension

Question 20

Will they fit the track on the Bosch RA1171? View answer

Answer posted 6 years ago | JessEm Clear-Cut Router Table Stock Guides

Question 21

Will the plate allow me to adjust a Triton 3 1/4 HP router? View answer

Answer posted 6 years ago | Infinity Tools Universal Router Table Top w/ JessEm Insert Plate

Question 22

My lock miter SR bit is dull after multiple passes. Can it be sharpened, and does sharpening affect the master jig? View answer

Answer posted 6 years ago | Infinity Tools 1/2" Shank Lock Miter Jr. Router Bit

Question 23

Will the router table RTT-002, JessEm fence RTF001, and Triton MOF001 with plate RTL-116 fit together? Any extra parts needed? View answer

Answer posted 6 years ago | Infinity Tools Aluminum Router Table Insert Plate, 9-1/4" x 11-3/4"

Question 24

Is there any offset to the dovetail/detail shark saw? View answer

Answer posted 6 years ago | Shark Corp. Dowel / Dovetail / Detail Saw

Question 25

I purchased an iris inlay with no instructions. The butterfly was clear, but I need instructions for the iris. View answer

Answer posted 6 years ago | Infinity Tools Iris - Multi-Layer Inlay System

Question 26

What is the kerf width on the 007-005 saw blade? View answer

Answer posted 6 years ago | Infinity Tools 160mm x 48T x 20mm Bore Track Master Saw Blade

Question 27

I am looking for a bit that will put a 5/8" wide cove on a door frame, I'm trying to match some doors for a freind. View answer

Answer posted 6 years ago | Infinity Tools 1/2" Shank Vertical Raised Panel Router Bits

Question 28

Will this fit the incra router table View answer

Answer posted 6 years ago | JessEm Rout-R-Lift II

Question 29

Does your plan have a itemized specification list for materials? View answer

Answer posted 6 years ago | Table Saw Out-feed Table

Question 30

Do they work with iPhones? View answer

Answer posted 6 years ago | Plugfones - Liberate 2.0 Bluetooth Earplug Headphones

Question 31

Can I swap the small bearing on the cove bit in the 3-piece raised panel set for a larger diameter bearing? View answer

Answer posted 6 years ago | Infinity Tools 1/2" Shank Horizontal Raised Panel Router Bits

Question 32

Where did you buy the table top? View answer

Answer posted 6 years ago | Table Saw Out-feed Table

Question 33

Can the carbide knives be sharpened when dull? View answer

Answer posted 6 years ago | Infinity Tools Carbide Tipped Knives For DeWalt 735 Planer - 3-Pc.

Question 34

Does the RTI-DIY template kit work with INCRA MagnaLOCK router plates and RTT-IRS rings? View answer

Answer posted 6 years ago | Infinity Tools 5-Pc. Router Insert Plate Template Package

Question 35

Can this plane be used to chamfer an edge? View answer

Answer posted 6 years ago | Infinity Tools Wood Jack Hand Plane

Question 36

Can this plane be used to chamfer an edge? View answer

Answer posted 6 years ago | Infinity Tools Wood Smoothing Hand Plane

Question 37

How does this same item fit both 20mm and 3/4" holes? is it a snug fit for 20mm and a sloppy fit for 3/4", or ??? View answer

Answer posted 6 years ago | BORA Self Adjusting In-Line Dog Clamp

Question 38

What does 'matched set' mean for the #91-505 Shaker 15 degree router bit set? Do they make perfect joints without shims? View answer

Answer posted 6 years ago | Infinity Tools 1/2" Shank Matched Rail & Stile Router Bits

Question 39

Are these blades double sided like factory ones or single sided like photo shows? View answer

Answer posted 6 years ago | Infinity Tools High Speed Steel Knives For DeWalt 734 Planer, 3-Pcs.

Question 40

How many blades will the 12" protector hold? View answer

Answer posted 6 years ago | Infinity Tools 8" Saw Blade Protector

Question 41

Can this clamp be used on a jig that clamps material below the clamp base, like making tapered legs for furniture? View answer

Answer posted 6 years ago | Bessey Auto Adjust Toggle Clamps

Question 42

Do you make a blade for the kapex View answer

Answer posted 6 years ago | Infinity Tools 12" Miter Saw Blade

Question 43

Hello, does the Triton 3-1/4 HP Dual Mode Precision Plunge Router; TRA001 come in the 220-240Voltage? View answer

Answer posted 6 years ago | Triton 3-1/4 HP Dual Mode Precision Plunge Router (TRA001)

Question 44

what diameter router bit will fit threw the base of the 31/4 hp router View answer

Answer posted 6 years ago | Triton 3-1/4 HP Dual Mode Precision Plunge Router (TRA001)

Question 45

how long are the carbide planner blades warrantied for? View answer

Answer posted 6 years ago | Infinity Tools Replacement Planer Knives for DeWalt DW734

Question 46

What?s the distance from the optional miter bar to the sled?s back edge? Need plate dimensions for router table setup. View answer

Answer posted 6 years ago | Infinity Tools Pro Coping Sled

Question 47

Will the Universal base fit a Black & Decker model 7612 Type 1 router? View answer

Answer posted 6 years ago | Infinity Tools Universal 7.5" Router Base Plate

Question 48

Does you starter carving tools come sharp and ready to use? View answer

Answer posted 6 years ago | Narex 5-Pc. Starter Carving Chisel Set

Question 49

Can I remove the bearing from your flush cut router bits to trim laminate below the surface, or do you have a better option? View answer

Answer posted 6 years ago | Infinity Tools 1/2" Shank Mega Flush Trim Router Bits

Question 50

Is this Table Saw Setup and Sanding Disk available with a 30mm bore for my Minimax C26 table saw? View answer

Answer posted 6 years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'

Browse by Topic

Tools