Question 1

Do all router corner radius templates fit 3/4" mega flush trim bits, or are some templates too small for large bits? View answer

Asked 4 ´years ago | Infinity Tools Corner Radius Template Guides; 3-Pc. Set

Question 2

Will this work with the RA1171 Bosch router table? View answer

Asked 6 ´years ago | Infinity Tools Vertical Router Sled

Question 3

Can I safely use the 8" dado blade for 1.5" wide by 1.75" deep dados with a 2 hp cabinet saw in multiple passes? View answer

Asked 4 ´years ago | Infinity Tools Dadonator Jr., 6" Stacked Dado Saw Blade Set

Question 4

will the eliminator chuck fit my Freud FT2000E router? View answer

Asked 4 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 5

BSB-098.125. Band saw blade Is this a set of 3 or just one ? View answer

Asked 5 ´years ago | Infinity Tools Resaw Bandsaw Blades

Question 6

Will old DeWalt 733 planer knives fit the new DeWalt 735 3-knife planer? View answer

Asked 6 ´years ago | Infinity Tools Carbide Tipped Knives For DeWalt 735 Planer - 3-Pc.

Question 7

What is the minimum thickness of the wood that you can use on this vertical router sled? View answer

Asked 4 ´years ago | Infinity Tools Vertical Router Sled

Question 8

Will the 8” Dadonator fit a SawStop cabinet saw? Is the diameter truly 8”, or could it be slightly larger? View answer

Asked 6 ´years ago | Infinity Tools Dadonator Jr., 6" Stacked Dado Saw Blade Set

Question 9

Does the dadonator blade fits on all job sites table saw ? View answer

Asked 6 ´years ago | Infinity Tools Dadonator Jr., 6" Stacked Dado Saw Blade Set

Question 10

The dado set’s outer blades seem to cause chipping. Shouldn't they have a higher tooth count for plywood? View answer

Asked 5 ´years ago | Infinity Tools Dadonator Jr., 6" Stacked Dado Saw Blade Set

Question 11

I ordered door-making templates but can’t find the swivel hold-down shown in the video. Where can I get it? View answer

Asked 6 ´years ago | Infinity Tools Frame & Panel Master - Door Making Jig For Your Router

Question 12

Interested in your crown template set. Which jig should be used with these templates? The video didn’t clarify. View answer

Asked 5 ´years ago | Infinity Tools Frame & Panel Master - Door Making Jig For Your Router

Question 13

Are the non-slip pads replaceable? View answer

Asked 5 ´years ago | Bloque de empuje con gancho inteligente MicroJIG GRR-RIP

Question 14

Could this jig accommodate a 28" table leg taper? View answer

Asked 5 ´years ago | MicroJIG Microdial Tapering Jig - Table Saw & Router Table

Question 15

Looking for 701/2 x 1/2 and 6 tpi band saw blade View answer

Asked 5 ´years ago | Infinity Tools Resaw Bandsaw Blades

Question 16

Can the work on left and right side of the blade? View answer

Asked 6 ´years ago | INCRA Miter EXPRESS

Question 17

Can I view a video of the IBOX Box Joint Jig and download the manual before purchasing? View answer

Asked 6 ´years ago | INCRA I-BOX - Box Joint Jig For Table Saw & Router Table

Question 18

does it come with miter fence? View answer

Asked 5 ´years ago | INCRA Miter EXPRESS

Question 19

What's in the box for $169.90? I.E. Does it come with the work piece hold down clamp? View answer

Asked 5 ´years ago | INCRA Miter EXPRESS

Question 20

I have an 8mm chuck router. Is there a 12mm or 1/2” extension available? I need a milling cutter for that clamping head. View answer

Asked 5 ´years ago | Infinity Tools Router Collet Xtreme Xtension

Question 21

With a Milwaukee 5625-20 router on a Jessem Master-R-Lift 11, how much of the router bit will be above the lift’s top when fully lowered? View answer

Asked 7 ´years ago | Infinity Tools Router Collet Xtreme Xtension

Question 22

Will these work with my Rigid "R4513" 10" Jobsite tablesaw and my Incra 1000 Miter Gauge? View answer

Asked 5 ´years ago | INCRA Miter EXPRESS

Question 23

Will the RTT-002 router table work with my Incra 25" Positioner and Wonder Fence? View answer

Asked 4 ´years ago | Infinity Tools Plycore Router Table Top, 24" x 32" x 1-1/8" Thick

Question 24

What thickness of insert plate will this table accept - 3/8"? View answer

Asked 6 ´years ago | Infinity Tools Plycore Router Table Top, 24" x 32" x 1-1/8" Thick

Question 25

Should I get the stainless plate if I’m buying the RTT-002 Router Table Top with Microdot Slick Surface? View answer

Asked 5 ´years ago | Infinity Tools Plycore Router Table Top, 24" x 32" x 1-1/8" Thick

Question 26

Do you have a schematic of the router table's bottom with connection info? I want to build a stand before it arrives. View answer

Asked 4 ´years ago | Infinity Tools Plycore Router Table Top, 24" x 32" x 1-1/8" Thick

Question 27

I love my track saw! Can I buy just 1/2 inch router bearings separately? I need them for my bits and router collet. View answer

Asked 5 ´years ago | Infinity Tools 33-Pc. Router Bit Bearing Emergency Kit

Question 28

Would the Incra Miter V120 work with this or does one need to get another miter gage? View answer

Asked 4 ´years ago | INCRA Miter EXPRESS

Question 29

Does the Express come with a fence? If so what size? Does it come with the stop block? Thanks. View answer

Asked 5 ´years ago | INCRA Miter EXPRESS

Question 30

Is this recommended for SawStop cabinet saws? If not, can you suggest another option? View answer

Asked 5 ´years ago | Infinity Tools Dadonator Jr., 6" Stacked Dado Saw Blade Set

Question 31

Is the 8" Dadonator set comparable with SawStop? View answer

Asked 6 ´years ago | Infinity Tools Dadonator Jr., 6" Stacked Dado Saw Blade Set

Question 32

Which router bit do you recommend for use with the corner radius template guide? View answer

Asked 6 ´years ago | Infinity Tools Corner Radius Template Guides; 3-Pc. Set

Question 33

Is double-sided tape a viable alternative to screws for securing the plate, to avoid damage? View answer

Asked 6 ´years ago | Infinity Tools Corner Radius Template Guides; 3-Pc. Set

Question 34

Can these be used without wood screws to hold the template, possibly with double-sided tape? View answer

Asked 6 ´years ago | Infinity Tools Corner Radius Template Guides; 3-Pc. Set

Question 35

Do the radius cutting templates include four adjustment pins? If not, what is the diameter of the pins? View answer

Asked 5 ´years ago | Infinity Tools Corner Radius Template Guides; 3-Pc. Set

Question 36

Does the 00-SSD include the metal disc for setting up a sanding disc on a 10” Craftsman table saw? View answer

Asked 5 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'

Question 37

Hi, does this switch com with a bracket to mount on a router table View answer

Asked 4 ´years ago | Infinity Tools Power Tool Safety On & Off Switch

Question 38

Part no. PKJ-201, Are these made out of steel or plastic ? View answer

Asked 4 ´years ago | Infinity Tools Planer & Jointer Knife Setting Jig - (Full Size Planers; Pair)

Question 39

I need a safety switch for a table saw that won't restart after a power outage until I press the start button. Any recommendations? View answer

Asked 6 ´years ago | Infinity Tools Power Tool Safety On & Off Switch

Question 40

Can the replaceable insert slide in/out without unscrewing the aluminum part like the Bosch model? View answer

Asked 5 ´years ago | Infinity Tools Festool Kapex KS 120 Miter Saw Z.C.I.

Question 41

Is the Festool Kapex KS 120 zero clearance insert listing correct? Do I need one or two plates for a complete set? View answer

Asked 5 ´years ago | Infinity Tools Festool Kapex KS 120 Miter Saw Z.C.I.

Question 42

Looking for safety paddles for a 15A Ridgid table saw. Do you have a paddle switch for that horsepower? View answer

Asked 5 ´years ago | Infinity Tools Power Tool Safety On & Off Switch

Question 43

I have a Craftsman 10" Table Saw Model # 113.299040 will this Big Gulp fit it or just the 14" flange? View answer

Asked 5 ´years ago | Infinity Tools Big Gulp Dust Hood

Question 44

For an old Craftsman table saw, I need a 4" to 2-1/2" reducer and 2-1/2" hose. Do you carry these? View answer

Asked 6 ´years ago | Infinity Tools Big Gulp Dust Hood

Question 45

Will this jig work on the 15" Delta DC planer? View answer

Asked 6 ´years ago | Infinity Tools Planer & Jointer Knife Setting Jig - (Full Size Planers; Pair)

Question 46

Is this a mechanical switch, not momentary or magnetic? I need a non-momentary paddle switch. View answer

Asked 5 ´years ago | Infinity Tools Power Tool Safety On & Off Switch

Question 47

Will this fit the kapex reb 120? (The newest kapex model) View answer

Asked 4 ´years ago | Infinity Tools Festool Kapex KS 120 Miter Saw Z.C.I.

Question 48

Are Pfeil chisels pre-sharpened and ready to use? If unsatisfied, can they be returned? View answer

Asked 6 ´years ago | Narex 8-Pc. Professional Carving Chisel Set

Question 49

I purchased the plans expecting to see a cut list of parts, no? What width of boards are the plans made from; 5/8? View answer

Asked 6 ´years ago | Slab Flattening Router Jig Plans

Question 50

This setup isn't secure; T-slots and cam clamps would be safer. View answer

Asked 6 ´years ago | Slab Flattening Router Jig Plans

Browse by Topic

Tools