Question 1

Will this work with a Sawstop Jobsite saw fence? View answer

Asked 7 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 2

What is the manufacturing tolerance for the $20 brass setup bar set? Is it made in the USA or China? View answer

Asked 7 ´years ago | Infinity Tools 5-Pc. Brass Bar Set For Tool Set-Up

Question 3

Is there a router bit set for flat panel cabinet doors with Ovolo sticking that fits a 3HP router? View answer

Asked 7 ´years ago

Question 4

do you have a brass router guide set to fit Makita RT0700C ? View answer

Asked 7 ´years ago | Shop Fox 10-Pc. Brass Template Guide Kit

Question 5

I’m having issues with the inlay plug fitting the cut-out hole. What’s the outside diameter of your collar? View answer

Asked 7 ´years ago | Infinity Tools Brass Inlay Kit w/ Spiral Bit & Centering Pin

Question 6

Do you have a router bit for cutting a 1" dado and 5/8" height in foam block? View answer

Asked 7 ´years ago | Infinity Tools 1/4" Shank Dado Router Bit

Question 7

Looking to replace a router bit bearing: 3/16 ID x 5/8 OD x 1/8 width. Is the BR-106 bearing width available? View answer

Asked 7 ´years ago | Infinity Tools 3/16" x 3/8" Bearing

Question 8

For a router table purchase, which lift do you use with the Triton? Can I use another router if it fails? View answer

Asked 7 ´years ago | Infinity Tools Pro Router Table Package with Triton 3-1/4 HP Router (TRA001)

Question 9

Does the star inlay set include three sizes for different woods, or just one size with different collars? I need clarification. View answer

Asked 7 ´years ago | Infinity Tools Nested Star - Multi-Layer Inlay System

Question 10

Will General Finishes High Performance Water-Based Urethane keep maple white? Can I top it with Arm-R-Seal without yellowing? View answer

Asked 7 ´years ago | General Finishes High Performance Top Coat

Question 11

Does this guide fit a porter cable router View answer

Asked 7 ´years ago | Milescraft Router Circle Guide Kit

Question 12

Do you make 30mm arbor box joint blades? View answer

Asked 7 ´years ago | Infinity Tools 8" Flat-Top Dado Saw Blade - 5/32" Kerf

Question 13

Can I get replacement magnets for the 11th finger? Mine keep falling out and are unfindable. View answer

Asked 7 ´years ago | FastCap 11th Finger, palo de empuje magnético de seguridad

Question 14

Will this work with 4" knives? View answer

Asked 7 ´years ago | Deulen 6" Jointer Knife Sharpener - For Knives Up To 8" Long

Question 15

Do you make a 17/32 x 7 degree x 1/2 shank dovetail bit? View answer

Asked 7 ´years ago | Brocas para fresadora de cola de milano con vástago de 1/4" de Infinity Tools

Question 16

Does the dadonator blade fits on all job sites table saw ? View answer

Asked 7 ´years ago | Infinity Tools Dadonator Jr., 6" Stacked Dado Saw Blade Set, 5/8" Bore

Question 17

Is this pricing per blade or for a set of three? View answer

Asked 7 ´years ago | Infinity Tools High Speed Steel Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets

Question 18

I bought the Celtic Knot template. Is there a video or guide for proper use and flipping of the template? View answer

Asked 7 ´years ago | Infinity Tools Celtic Knot - Multi-Layer Inlay System

Question 19

is this model available in 8 1/4 x 11 3/4 View answer

Asked 7 ´years ago | JessEm Rout-R-Lift II

Question 20

Which router plate fits Milwaukee 5616-24 best: Jessem, Infinity, or Woodpeckers? It must align exactly with minimal excess holes. View answer

Asked 7 ´years ago | JessEm Rout-R-Plate

Question 21

Do you sell individual bearings for router bits? I dropped my 06-694 bit and damaged the bearing. View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Mega Flush Trim Router Bits

Question 22

Can I use a Freud ogee bit with item HDFPM-201 or do I need another bit? View answer

Asked 7 ´years ago | Infinity Tools HD Frame & Panel Master With Cathedral Door Templates

Question 23

will this fit into a Bosch router table RA1181? View answer

Asked 7 ´years ago | JessEm Rout-R-Lift II

Question 24

I need to replace old window trim (2.75 x 0.75 fluted edges). Can you suggest a router bit or alternative? View answer

Asked 7 ´years ago | Infinity Tools 1/4" Shank Roundover & Beading Router Bits

Question 25

will this fit on a rigid planer? View answer

Asked 7 ´years ago | Wixey 0" - 6" Digital Planer Readout - For Portable Planers

Question 26

Is there anyway to order the e-Bush (e7) by it's self? View answer

Asked 7 ´years ago | Leigh 11-Pc. RTJ400 Accessory Router Bit & Bushing Kit

Question 27

Do you offer set-up blocks for the 3-Pc. Ultimate Glass Door Making Router Bit Set? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank 3-Pc. Ultimate Glass Door Making Router Bit Set

Question 28

Will the Incra crosscut sled work with a SawStop? Is it adjustable enough? View answer

Asked 7 ´years ago | INCRA Miter EXPRESS

Question 29

Can I leave my dust collector on with gates open for multiple cuts? I use both 240V and 120V tools. View answer

Asked 7 ´years ago | iVac Automatic Vacuum Switch Box

Question 30

Does the 2 1/4 hp. model have the same on/off switch issue as the 3 1/4 hp. model? Has it been fixed? View answer

Asked 7 ´years ago | Triton 2-1/4 HP (1400w) Dual Mode Plunge Router (MOF001)

Question 31

Does this combo include the crank to raise and lower the router in a table View answer

Asked 7 ´years ago | Infinity Tools Aluminum Router Table Insert Plate, 9-1/4" x 11-3/4"

Question 32

Trying to find 12 3/8 blades for Ryobi AP-12 Planer View answer

Asked 7 ´years ago | Infinity Tools High Speed Steel Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets

Question 33

Can your venturi work with a Husky Air Compressor for silicone degassing? Smooth-on requires 29 in mercury and 8 CFM. View answer

Asked 7 ´years ago | Infinity Tools Venturi Vacuum System

Question 34

Work with 1/2 inch bit? View answer

Asked 7 ´years ago | Infinity Tools Aluminum Router Table Insert Plate, 9-1/4" x 11-3/4"

Question 35

Will your kits work with a FESTOOL router? View answer

Asked 7 ´years ago | Infinity Tools Clownfish - Multi-Layer Inlay System

Question 36

How wide are the imaging rulers? View answer

Asked 7 ´years ago | iGaging 4R Rule

Question 37

Can you get the queen anne router bit without the bearing? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Queen Anne Router Bit

Question 38

I need a router bit for 2.5” deep mortises in hard maple. Any recommendations for making flat-bottomed mortises? View answer

Asked 7 ´years ago | Infinity Tools 1/4" Shank Solid Carbide Spiral Upcut Router Bits

Question 39

Is the push rod on these plastic or metal? View answer

Asked 7 ´years ago | BORA Self Adjusting In-Line Dog Clamp

Question 40

Will the ZCI insert work on my 12" slide miter saw. View answer

Asked 7 ´years ago | Infinity Tools Zero Clearance Insert (Z.C.I.) Plate for DeWalt 10" & 12" Non-Sliding Saws

Question 41

What is the country of origin? View answer

Asked 7 ´years ago | iGaging 3-in-1 Digital Marking & Mortise Gauge

Question 42

do you sell the sled table only? I already own the incra1000hd. View answer

Asked 7 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 43

I was wondering which jig would work best for the miter bit I have. Thank you for you help! View answer

Asked 7 ´years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 44

Is the 3 pc set ,bit extension collet and base plate shank diameter half inch? View answer

Asked 7 ´years ago | Infinity Tools 3- Pc. Planer's Package for Routers

Question 45

Is Sears router 175040 is the same as 17540 View answer

Asked 7 ´years ago | JessEm Rout-R-Lift II

Question 46

What is the shank size of router bits? Can I get 1/4 inch bits? View answer

Asked 7 ´years ago | Milescraft SignPro Kit

Question 47

I need the 83-034 bevel cutters in an 1 1/4" bore. Available ? View answer

Asked 7 ´years ago | Infinity Tools Cabinet Door Rail & Stile Shaper Cutter Sets, 3/4" Bore

Question 48

Will this unit work on an INCA 259 table saw? If so, do you have pictures of the set up? View answer

Asked 7 ´years ago | iGaging 0" - 36" Digital Table Saw Fence Readout

Question 49

Hi- what is the outside diameter of the collet? View answer

Asked 7 ´years ago | Infinity Tools Router Bit Collet Extension

Question 50

Do I need to purchase the template guides separately or are they included with the multi-layer inlay system? View answer

Asked 7 ´years ago | Infinity Tools 4" Butterfly - Multi-Layer Inlay System

Browse by Topic

Tools