Question 1

Can I use a Freud ogee bit with item HDFPM-201 or do I need another bit? View answer

Asked 6 ´years ago | Infinity Tools HD Frame & Panel Master With Cathedral Door Templates

Question 2

How much extra material should be planned when cutting 3/4" thick stock with a 22.5° Lock Miter Bit Set? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank 22.5° Lock Miter Router Bit Set w/ Setup Block

Question 3

Can I make multiple passes with a 3-1/4 HP router for a lock miter bit to cut 1 ply, or is there a better method? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Lock Miter Jr. Router Bit

Question 4

Hi I have Freud lock miter router bit I need to know if lock miter master jigs work , with thank. , Oscar View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Lock Miter Jr. Router Bit

Question 5

Can the Lock Miter SR cut miters in 5/8” to 11/16”? I want to avoid needing two bits for 13/16” and 5/8” miters. View answer

Asked 5 ´years ago | Infinity Tools 1/2" Shank Lock Miter Jr. Router Bit

Question 6

I have the 45 degree lock miter junior and will be using it on 3/4" plywood. What RPM should I use? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Lock Miter Jr. Router Bit

Question 7

Will this work with a Skil 3410? View answer

Asked 6 ´years ago | Infinity Tools Table Saw Dust Collector - Dust Cutter

Question 8

Will the Dust Cutter II fit my SkillSaw 3400 (21 7/8 x 18 1/2 base) and work with a 1/2" ShopVAC hose? View answer

Asked 6 ´years ago | Infinity Tools Table Saw Dust Collector - Dust Cutter

Question 9

Will it work with a four inch dust collector hose? View answer

Asked 6 ´years ago | Infinity Tools Table Saw Dust Collector - Dust Cutter

Question 10

For two hard-to-reach blast gates, can I use two Automated Pro Blast Gates with iVac Pro Tool Plus units? View answer

Asked 5 ´years ago | iVac Pro Remote

Question 11

Can two blast gates open simultaneously for a table saw’s base and guard dust collection while others stay closed? View answer

Asked 5 ´years ago | iVac Pro Switch; 240Vac; 20A

Question 12

I have an older craftsman saw will it work on my saw and does this replace my fence or work with it View answer

Asked 6 ´years ago | Wixey 0" - 60" Digital Table Saw Fence Readout

Question 13

The iVac Pro Switch page shows a 115V plug, but I need to confirm the 220V model has the correct 220V plug with horizontal blade. View answer

Asked 5 ´years ago | iVac Pro Switch; 240Vac; 20A

Question 14

How short can the 115-070 collet extension be adjusted? Is it fixed at 2 1/4" or can it be shortened? View answer

Asked 5 ´years ago | Infinity Tools Router Bit Collet Extension

Question 15

Will this work on a Steel City cabinet grade table saw using a 10" saw blade? View answer

Asked 6 ´years ago | Betterley Tru-Cut Insert System For Delta Right Tilt Unisaw

Question 16

Can the Ivac switch work on two circuits simultaneously? My Shop-Vac is on 20 amps and other devices on 15 amps. View answer

Asked 6 ´years ago | iVac Automatic Vacuum Switch Box

Question 17

For the 3-piece pro door set with a 3/4” spindle, should I use the tall bushing in the stile middle? View answer

Asked 5 ´years ago | Infinity Tools 2-Pc. T-Bushing Set

Question 18

Can I leave my dust collector on with gates open for multiple cuts? I use both 240V and 120V tools. View answer

Asked 6 ´years ago | iVac Automatic Vacuum Switch Box

Question 19

Will this switch work with a Saw Stop? View answer

Asked 7 ´years ago | iVac Automatic Vacuum Switch Box

Question 20

This looks great! Any way to do 3/4" dados I. One pass? View answer

Asked 6 ´years ago | Infinity Tools Precision Router Dado Jig

Question 21

Bought PDT-101HD templates; why don’t the Panel and Stile templates fit together like a puzzle? Are they defective? View answer

Asked 6 ´years ago | Infinity Tools HD Cathedral Door Making Templates; 20-Pcs.

Question 22

How do I operate multiple tools without switching plugs? Do I need multiple boxes or does this control one tool? View answer

Asked 5 ´years ago | iVac Automatic Vacuum Switch Box

Question 23

What is the "auxillary" output for? View answer

Asked 5 ´years ago | iVac Automatic Vacuum Switch Box

Question 24

Hi. We drill the holes in jig to fit our own router. So it will adapt to any router, is that correct. View answer

Asked 6 ´years ago | Infinity Tools Fluting Jig For Straight & Arched Stock

Question 25

Can I buy just the 3/4" bit from the plug cutter set 101-208? It's my favorite, but I don’t need the whole set. View answer

Asked 6 ´years ago | Infinity Tools 5-Pc. Extra Long Dowel & Plug Cutter Set

Question 26

I need a plug cutter with a drill bit mounted in the shaft for drilling holes in small dowels. Can you help with this? View answer

Asked 7 ´years ago | Infinity Tools 5-Pc. Extra Long Dowel & Plug Cutter Set

Question 27

Can lapped miter joint router bits be used in a handheld router, or are they only for router tables? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Lapped Miter Joint Router Bit Set w/ 3/4" Setup Block

Question 28

Do you stock 7/16” and 7/8” bits for the 5-Pc. Extra Long Dowel & Plug Cutter Set? View answer

Asked 6 ´years ago | Infinity Tools 5-Pc. Extra Long Dowel & Plug Cutter Set

Question 29

Will this work with 5/8” PVC for column trim bases? The old joints used something similar. View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Lapped Miter Joint Router Bit Set w/ 3/4" Setup Block

Question 30

We need 2” carbide Forstner bits. Can they drill a flat bottom hole in concrete? View answer

Asked 7 ´years ago | Infinity Tools 7-Pc. Carbide Tipped Forstner Bit Set

Question 31

Do you sell a zero clearance plate that fits Grizzly G0690 table saws? View answer

Asked 5 ´years ago | Betterley Tru-Cut Insert System For Delta Right Tilt Unisaw

Question 32

Will this product work on the Hammer C3-31 Combination machine? My European sliding table saw has a poor rip fence. View answer

Asked 7 ´years ago | Wixey 0" - 60" Digital Table Saw Fence Readout

Question 33

If I buy two Wixey table saw readouts, can I connect measuring sticks for a 120-inch miter saw station? View answer

Asked 5 ´years ago | Wixey 0" - 60" Digital Table Saw Fence Readout

Question 34

Does the M-Power Fasttrack Sharpening System work for Flexcut carving tools, or do you have a similar system? View answer

Asked 6 ´years ago | MPOWER Diamond DeBurring Plate For PSS

Question 35

Are the CIK-193 cutters for the Insert-Pro rail and stile cutter sold individually or as a set? I need another edge style option. View answer

Asked 6 ´years ago | Infinity Tools Replacement Knife for Insert-Pro Combination Rail and Stile Shaper Cutter

Question 36

Any setup tips for using the glue joint shaper cutter? I’m struggling with trial and error. View answer

Asked 5 ´years ago | Infinity Tools Reverse Glue Joint Shape-Up Shaper Cutter, 3/4" Bore

Question 37

How can I change the angle from 25 to 30 degrees with this system? View answer

Asked 6 ´years ago | MPOWER Diamond DeBurring Plate For PSS

Question 38

Will the fast track sharpen my dog grooming, clipper blades? I have Oster dog grooming clippers. View answer

Asked 6 ´years ago | MPOWER Diamond DeBurring Plate For PSS

Question 39

Is there an extended tenon cutter for the 91-527 set mission style. I see one for the Ogee and Shaker View answer

Asked 5 ´years ago | Infinity Tools 1/2" Shank Interior & Exterior Door Router Bit Set

Question 40

For glue joint shaper cutters 83-120 or 84-120, what spindle is used for the bore hole? Seems like buying a car without an engine. View answer

Asked 7 ´years ago | Infinity Tools Reverse Glue Joint Shape-Up Shaper Cutter, 3/4" Bore

Question 41

How much panel gap do I allow for the space balls? View answer

Asked 7 ´years ago | Infinity Tools Space Balls 1/4"; 250 pack

Question 42

I bought the 00-527 profiles. Your site says "entry and passage doors" but the photos show cabinet doors. Can they be used for cabinets? View answer

Asked 5 ´years ago | Infinity Tools 1/2" Shank Interior & Exterior Door Router Bit Set

Question 43

1) What is the depth of cut with these blades? 2) Will they fit on my FEIN Multimaster? View answer

Asked 7 ´years ago | Imperial Blades 3-Pc. Multi-Tool Blade Package - Universal Fit

Question 44

Do you sell a 5/8" straight plug cutter as well as a 5/8" Forstner drill separately ( not in a Kit or set) View answer

Asked 5 ´years ago | Infinity Tools 8-Pc. Plug Cutter & Tenon Set - Straight & Tapered Styles

Question 45

What is the total length of the 101-039 5mm bit? I need a 5-inch long Brad point bit. View answer

Asked 7 ´years ago | Snappy #2 & #3 (5/64") Self Centering Bit

Question 46

Can I buy the 36" fence and brackets separately for the Magswitch work holding starter kit? Do you have a taller fence? View answer

Asked 6 ´years ago | Magswitch 18" Universal T-Track Fence

Question 47

Can you quote for an oval Branding Iron with "Hand Crafted By Duane Conrad"? View answer

Asked 7 ´years ago

Question 48

Can you make an electric branding iron with 1/2" tall letters for a line of 11 letters, a blank line, and 6 letters below? View answer

Asked 7 ´years ago

Question 49

I have a Craftsman 12" bandsaw. Model #113.248210. The tabletop is 17.5 in long. Will this fit? View answer

Asked 6 ´years ago | Infinity Tools PRO-Grip Universal Fence Attachment

Question 50

My 12" Craftsman Band-saw has a 26.5" table. Will the fence attachment fit on a 36" straight edge clamp for my saw? View answer

Asked 6 ´years ago | Infinity Tools PRO-Grip Universal Fence Attachment

Browse by Topic

Tools