Question 1

Will the Table Saw Dust Collector II (115-116) fit my Skil 3410-02 saw with a folding stand? The design might affect compatibility. View answer

Asked 7 ´years ago | Milescraft Table Saw Dust Collector - Dust Cutter

Question 2

Is there a shop in Houston, TX where I can see the Infinity Router Table with the Triton router before buying? View answer

Asked 7 ´years ago | Infinity Tools Pro Router Table Package with Triton 3-1/4 HP Router (TRA001) & Cast Iron Top

Question 3

Can the JessEm Dowel Jig Master Kit drill dowel holes at a 45-degree angle, like for drawer sides and ends? View answer

Asked 7 ´years ago | JessEm Dowel Jig Master Kit

Question 4

will the porter cable style bushing fit this router ? View answer

Asked 7 ´years ago | Triton 3-1/4 HP Dual Mode Precision Plunge Router (TRA001)

Question 5

Do you have a tongue and groove router bit set with 1/4" shanks? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Tongue & Groove Router Bit Sets

Question 6

What’s the shank size on these bits? Can smaller bits be used in a portable drill for teak deck bungs? View answer

Asked 7 ´years ago | Infinity Tools 7-Pc. Carbide Tipped Forstner Bit Set

Question 7

who makes the cast iron top View answer

Asked 7 ´years ago | Infinity Tools Pro Router Table Package with Triton 3-1/4 HP Router (TRA001) & Cast Iron Top

Question 8

Does this bit have carbide cutting blades? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Drawer Locking Router Bit

Question 9

I would like to purchase product #100-184, but no diamentions are shown. Looking for 3/4 inch View answer

Asked 7 ´years ago | Infinity Tools Card Set - Multi Layer Inlay System

Question 10

How can I tell if your sizes fit the collet threading on my Grizzly shaper? View answer

Asked 7 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 11

Do you have a clearance plate with replaceable centers for a Shop Fox W1820 like the one for Saw Stop? View answer

Asked 7 ´years ago | Betterley Tru-Cut Insert System For Delta Right Tilt Unisaw

Question 12

I need a shaper bit for glue joint that will work on 2" wood, like a 2x6. Do you have anything like that? View answer

Asked 7 ´years ago | Infinity Tools Reverse Glue Joint Shape-Up Shaper Cutter, 3/4" Bore

Question 13

What is the shelf life on most glues? I use primarily Titebond, Elmers and Gorilla glues. View answer

Asked 7 ´years ago | FastCap BabeBot, 4 oz.

Question 14

Will JessEm ClearCut stock guides work with a Powermatic 5 HP shaper? Power feeder is costly; wondering if they work. View answer

Asked 7 ´years ago | JessEm Clear-Cut Router Table Stock Guides

Question 15

Is there a pattern bit with a 3/8" or smaller diameter cutter head and guide bearing on top? The 85-120 doesn’t fit my needs. View answer

Asked 7 ´years ago | Infinity Tools 1/4" Shank x 1/4" Cutter Diameter x 1" Cutter Length. Solid Carbide Spiral Flush Trim Router Bits

Question 16

Using the largest bearing - what is the shallowest cut allowable? Thanks. View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank 11-Pc. Slot Cutter Master Set

Question 17

Product 05-000 Floating Lettering Bit...What is the overall length? View answer

Asked 7 ´years ago | Infinity Tools 1/4" Shank Floating Lettering Bit

Question 18

For the 83-034 shaker cutters, which direction should they run and at what RPM? What feed direction to use? View answer

Asked 7 ´years ago | Infinity Tools Cabinet Door Rail & Stile Shaper Cutter Sets, 3/4" Bore

Question 19

Hello I got your 4pc flat top saw pkg last month How do you go about getting the cheat sheet on the video. View answer

Asked 7 ´years ago | Infinity Tools 4pc. Thick Kerf Flat-Top Saw Blade Package - 5/8" Arbor

Question 20

Is there such a thing as a adapter for routers that work with 1/4in shaft bits to take 1/2in router bits..? View answer

Asked 7 ´years ago | Infinity Tools 1/4" Shank Dado Router Bit

Question 21

will this product fit a Delta 10" contractor saw, model 36-426? View answer

Asked 7 ´years ago | Milescraft Table Saw Dust Collector - Dust Cutter

Question 22

I have an older shaper with a 1/2" spindle. Can you supply cutters for that or provide a sleeve to fit a 3/4" or 1" spindle? View answer

Asked 7 ´years ago | Infinity Tools Shape-Up Crown Molding Shaper Cutter, 1" Bore

Question 23

I need blades for a 12" CKM jointer. Specs: 3/4" to 1" wide and 1/8" thick. Do you have suitable blades? View answer

Asked 7 ´years ago | Infinity Tools High Speed Steel Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets

Question 24

Is the blade thickness for the 010-124 less than .088"? It must be thinner than .088" with a kerf larger than .092". View answer

Asked 7 ´years ago | Infinity Tools 10" Table Saw Ripping Blade - Thin Kerf

Question 25

Your large 1/2" x 2" flush cutter runs max at 16K rpm. How can I ensure it’s not running too fast on my Dewalt DW618? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Mega Flush Trim Router Bits

Question 26

I have Ridgid TS3660. Will JessEm - Clear-Cut Stock Guides For Table Saws fit Ridgid TS3660 fence? View answer

Asked 7 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 27

How do the blades in the essential package compare to a woodworker II blade? View answer

Asked 7 ´years ago | Infinity 2-Pc. 8" Dadonator & Full Kerf Super General Saw Blade Package, 5/8" Bore

Question 28

Can the 61-507 T&G set be used with the 90-502 raised panel bit for 5.5/5.9 mm plywood by adjusting the depth? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Horizontal Raised Panel Router Bits

Question 29

Sharpening resale bandsaw blades? View answer

Asked 7 ´years ago | Infinity Tools Resaw Bandsaw Blades

Question 30

What model is this item? View answer

Asked 7 ´years ago | HomeRight Super Finish Max Paint Sprayer

Question 31

Would this device sharpen chisels and planer blades as well View answer

Asked 7 ´years ago | Work Sharp Ken Onion 5-Pc. Blade Grinder Attachment Belt Kit

Question 32

Do you have a jointer knife jig for 12" jointer? View answer

Asked 7 ´years ago | Infinity Tools Jointer Knife Jig - For Carbide or Steel Knives 4"- 8"

Question 33

do you have a picture of the different profiles for the router cabinet kits? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank 3-Pc. Cabinetmaker's Combo Router Bit Set w/ Backcutter & FREE Setup Block

Question 34

can I get a 5 ft combination miter & t track so I don't have to spice it . I will need two. Thanks View answer

Asked 7 ´years ago | Infinity Tools 32" Miter & Mini T-Track Combination

Question 35

Are these blades able to be ran in a saw stop? View answer

Asked 7 ´years ago | Infinity 2-Pc. 8" Dadonator & Full Kerf Super General Saw Blade Package, 5/8" Bore

Question 36

I have an older square D type box for my 220v table saw. Do you have 220v versions? View answer

Asked 7 ´years ago | Infinity Tools Power Tool Safety On & Off Switch

Question 37

What is the size of the bit in this package View answer

Asked 7 ´years ago | Infinity Tools Precision Router Dado Jig

Question 38

Will this also fit the infinity router lifts View answer

Asked 7 ´years ago | Milescraft Router Table Dust Collector

Question 39

Does this kit come with a carry case? View answer

Asked 7 ´years ago | iGaging 3-Pc. Machine Digital Setup Package

Question 40

Do your cutters ease shaped edges to prevent bridging when spray painting doors? View answer

Asked 7 ´years ago | Infinity Tools 1-Pc. Rail & Stile Cabinet Door Shape-Up Shaper Cutter

Question 41

What’s the tenon length on your rail cutter? I need a longer tenon for cabinet doors. Any recommendations? View answer

Asked 7 ´years ago | Infinity Tools 1-Pc. Rail & Stile Cabinet Door Shape-Up Shaper Cutter

Question 42

I’m interested in the professional router table package. Can I buy it without the Triton MOF001 router? View answer

Asked 7 ´years ago | Infinity Tools Pro Router Table Package with Triton 3-1/4 HP Router (TRA001)

Question 43

Can I buy new locking handles and slides? I have used these for a long time and have worn out the locks. View answer

Asked 7 ´years ago | Infinity Tools 2" Wide Pro-Grip Straight Edge Clamps

Question 44

Do you sell a 1/4" Shank Roundover & Beading Router Bit Set View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank 3-Pc. Roundover & Beading Router Bit Set

Question 45

Can these bearings be double stacked to create a wider surface so they will not dent soft wood? View answer

Asked 7 ´years ago | Infinity Tools 7-Pc. Rabbeting Bit Bearing Kit, 3/16" I.D.

Question 46

I need a 10” table saw blade with a 1/4” kerf for tenons. Can you provide a link on your site? View answer

Asked 7 ´years ago | Infinity Tools 10" Table Saw Ripping Blade - Thin Kerf

Question 47

Can I change the Delta DC380 planer blades to wire or nylon brushes for trim? Do you make these? View answer

Asked 7 ´years ago | Infinity Tools Carbide Tipped Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets

Question 48

Where are these iGaging rules made? View answer

Asked 7 ´years ago | iGaging 4R Rule

Question 49

hello what one would I used in my Dewalt DWE7480 Job site table saw this one # 010-045 or # 010-044 View answer

Asked 7 ´years ago | Infinity Tools 10" Super General Combination Table Saw Blade

Question 50

IS THERE ANY STORE IN UK WHERE I CAN PURCHASE 61-502. View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Horizontal Raised Panel Router Bits

Browse by Topic

Tools