Question 1

Does this combo include the crank to raise and lower the router in a table View answer

Asked 6 ´years ago | Infinity Tools Aluminum Router Table Insert Plate, 9-1/4" x 11-3/4"

Question 2

Trying to find 12 3/8 blades for Ryobi AP-12 Planer View answer

Asked 6 ´years ago | Infinity Tools High Speed Steel Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets

Question 3

Can your venturi work with a Husky Air Compressor for silicone degassing? Smooth-on requires 29 in mercury and 8 CFM. View answer

Asked 6 ´years ago | Venturi Vacuum System

Question 4

Work with 1/2 inch bit? View answer

Asked 6 ´years ago | Infinity Tools Aluminum Router Table Insert Plate, 9-1/4" x 11-3/4"

Question 5

Will your kits work with a FESTOOL router? View answer

Asked 6 ´years ago | Infinity Tools Clownfish - Multi-Layer Inlay System

Question 6

How wide are the imaging rulers? View answer

Asked 6 ´years ago | iGaging 4R Rule

Question 7

Can you get the queen anne router bit without the bearing? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Queen Anne Router Bit

Question 8

I need a router bit for 2.5” deep mortises in hard maple. Any recommendations for making flat-bottomed mortises? View answer

Asked 6 ´years ago | Infinity Tools 1/4" Shank Solid Carbide Spiral Upcut Router Bits

Question 9

Is the push rod on these plastic or metal? View answer

Asked 6 ´years ago | BORA Self Adjusting In-Line Dog Clamp

Question 10

Will the ZCI insert work on my 12" slide miter saw. View answer

Asked 6 ´years ago | Infinity Tools Zero Clearance Insert (Z.C.I.) Plate for DeWalt 10" & 12" Non-Sliding Saws

Question 11

What is the country of origin? View answer

Asked 6 ´years ago | iGaging 3-in-1 Digital Marking & Mortise Gauge

Question 12

do you sell the sled table only? I already own the incra1000hd. View answer

Asked 6 ´years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 13

I was wondering which jig would work best for the miter bit I have. Thank you for you help! View answer

Asked 6 ´years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 14

Is the 3 pc set ,bit extension collet and base plate shank diameter half inch? View answer

Asked 6 ´years ago | Infinity Tools 3- Pc. Planer's Package for Routers

Question 15

Is Sears router 175040 is the same as 17540 View answer

Asked 6 ´years ago | JessEm Rout-R-Lift II

Question 16

What is the shank size of router bits? Can I get 1/4 inch bits? View answer

Asked 6 ´years ago | Milescraft SignPro Kit

Question 17

I need the 83-034 bevel cutters in an 1 1/4" bore. Available ? View answer

Asked 6 ´years ago | Infinity Tools Cabinet Door Rail & Stile Shaper Cutter Sets, 3/4" Bore

Question 18

Will this unit work on an INCA 259 table saw? If so, do you have pictures of the set up? View answer

Asked 6 ´years ago | iGaging 0" - 36" Digital Table Saw Fence Readout

Question 19

Hi- what is the outside diameter of the collet? View answer

Asked 6 ´years ago | Infinity Tools Router Bit Collet Extension

Question 20

Do I need to purchase the template guides separately or are they included with the multi-layer inlay system? View answer

Asked 6 ´years ago | Infinity Tools 4" Butterfly - Multi-Layer Inlay System

Question 21

Will the Table Saw Dust Collector II (115-116) fit my Skil 3410-02 saw with a folding stand? The design might affect compatibility. View answer

Asked 6 ´years ago | Infinity Tools Table Saw Dust Collector - Dust Cutter

Question 22

Is there a shop in Houston, TX where I can see the Infinity Router Table with the Triton router before buying? View answer

Asked 6 ´years ago | Infinity Tools Pro Router Table Package with Triton 3-1/4 HP Router (TRA001) & Cast Iron Top

Question 23

Can the JessEm Dowel Jig Master Kit drill dowel holes at a 45-degree angle, like for drawer sides and ends? View answer

Asked 6 ´years ago | JessEm Dowel Jig Master Kit

Question 24

will the porter cable style bushing fit this router ? View answer

Asked 6 ´years ago | Triton 3-1/4 HP Dual Mode Precision Plunge Router (TRA001)

Question 25

Do you have a tongue and groove router bit set with 1/4" shanks? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Tongue & Groove Router Bit Sets

Question 26

What’s the shank size on these bits? Can smaller bits be used in a portable drill for teak deck bungs? View answer

Asked 6 ´years ago | Infinity Tools 7-Pc. Carbide Tipped Forstner Bit Set

Question 27

who makes the cast iron top View answer

Asked 6 ´years ago | Infinity Tools Pro Router Table Package with Triton 3-1/4 HP Router (TRA001) & Cast Iron Top

Question 28

Does this bit have carbide cutting blades? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Drawer Locking Router Bit

Question 29

I would like to purchase product #100-184, but no diamentions are shown. Looking for 3/4 inch View answer

Asked 6 ´years ago | Infinity Tools Card Set - Multi Layer Inlay System

Question 30

How can I tell if your sizes fit the collet threading on my Grizzly shaper? View answer

Asked 6 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 31

Do you have a clearance plate with replaceable centers for a Shop Fox W1820 like the one for Saw Stop? View answer

Asked 6 ´years ago | Betterley Tru-Cut Insert System For Delta Right Tilt Unisaw

Question 32

I need a shaper bit for glue joint that will work on 2" wood, like a 2x6. Do you have anything like that? View answer

Asked 7 ´years ago | Infinity Tools Reverse Glue Joint Shape-Up Shaper Cutter, 3/4" Bore

Question 33

What is the shelf life on most glues? I use primarily Titebond, Elmers and Gorilla glues. View answer

Asked 7 ´years ago | FastCap BabeBot, 4 oz.

Question 34

Will JessEm ClearCut stock guides work with a Powermatic 5 HP shaper? Power feeder is costly; wondering if they work. View answer

Asked 7 ´years ago | JessEm Clear-Cut Router Table Stock Guides

Question 35

Is there a pattern bit with a 3/8" or smaller diameter cutter head and guide bearing on top? The 85-120 doesn’t fit my needs. View answer

Asked 7 ´years ago | Infinity Tools - Brocas de carburo sólido para fresado en espiral con corte al ras (vástago de 1/4" x diámetro de fresa de 1/4" x longitud de fresa de 1")

Question 36

Using the largest bearing - what is the shallowest cut allowable? Thanks. View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank 11-Pc. Slot Cutter Master Set

Question 37

Product 05-000 Floating Lettering Bit...What is the overall length? View answer

Asked 7 ´years ago | Infinity Tools 1/4" Shank Floating Lettering Bit

Question 38

For the 83-034 shaker cutters, which direction should they run and at what RPM? What feed direction to use? View answer

Asked 7 ´years ago | Infinity Tools Cabinet Door Rail & Stile Shaper Cutter Sets, 3/4" Bore

Question 39

Hello I got your 4pc flat top saw pkg last month How do you go about getting the cheat sheet on the video. View answer

Asked 7 ´years ago | Infinity Tools 4pc. Thick Kerf Flat-Top Saw Blade Package - 5/8" Arbor

Question 40

Is there such a thing as a adapter for routers that work with 1/4in shaft bits to take 1/2in router bits..? View answer

Asked 7 ´years ago | Infinity Tools 1/4" Shank Dado Router Bit

Question 41

will this product fit a Delta 10" contractor saw, model 36-426? View answer

Asked 7 ´years ago | Infinity Tools Table Saw Dust Collector - Dust Cutter

Question 42

I have an older shaper with a 1/2" spindle. Can you supply cutters for that or provide a sleeve to fit a 3/4" or 1" spindle? View answer

Asked 7 ´years ago | Cortador de moldura de corona Shape-Up de Infinity Tools, orificio de 1"

Question 43

I need blades for a 12" CKM jointer. Specs: 3/4" to 1" wide and 1/8" thick. Do you have suitable blades? View answer

Asked 7 ´years ago | Infinity Tools High Speed Steel Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets

Question 44

Is the blade thickness for the 010-124 less than .088"? It must be thinner than .088" with a kerf larger than .092". View answer

Asked 7 ´years ago | Infinity Tools 10" Table Saw Ripping Blade - Thin Kerf

Question 45

Your large 1/2" x 2" flush cutter runs max at 16K rpm. How can I ensure it’s not running too fast on my Dewalt DW618? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Mega Flush Trim Router Bits

Question 46

I have Ridgid TS3660. Will JessEm - Clear-Cut Stock Guides For Table Saws fit Ridgid TS3660 fence? View answer

Asked 7 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 47

How do the blades in the essential package compare to a woodworker II blade? View answer

Asked 7 ´years ago | Paquete de 2 hojas de sierra Infinity de 8" con Dadonator y corte completo Super General, orificio de 5/8"

Question 48

Can the 61-507 T&G set be used with the 90-502 raised panel bit for 5.5/5.9 mm plywood by adjusting the depth? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Horizontal Raised Panel Router Bits

Question 49

Sharpening resale bandsaw blades? View answer

Asked 7 ´years ago | Infinity Tools Resaw Bandsaw Blades

Question 50

What model is this item? View answer

Asked 7 ´years ago | HomeRight Super Finish Max Paint Sprayer

Browse by Topic

Tools