Question 1

Which router bit do you recommend for use with the corner radius template guide? View answer

Answer posted 7 years ago | Infinity Tools Corner Radius Template Guides; 3-Pc. Set

Question 2

Are your router bits and setup blocks made in the USA or imported? View answer

Answer posted 7 years ago | Infinity Tools 8-Pc. Precision Tool & Project Setup Blocks

Question 3

Will base plate fit on a De Walt router? View answer

Answer posted 7 years ago | Milescraft SignPro Kit

Question 4

Can these be used without wood screws to hold the template, possibly with double-sided tape? View answer

Answer posted 7 years ago | Infinity Tools Corner Radius Template Guides; 3-Pc. Set

Question 5

Is double-sided tape a viable alternative to screws for securing the plate, to avoid damage? View answer

Answer posted 7 years ago | Infinity Tools Corner Radius Template Guides; 3-Pc. Set

Question 6

I ordered door-making templates but can’t find the swivel hold-down shown in the video. Where can I get it? View answer

Answer posted 7 years ago | Infinity Tools Frame & Panel Master - Door Making Jig For Your Router

Question 7

Do the router baseplates fit a Bosch PR20evs hand held model? View answer

Answer posted 7 years ago | Infinity Tools Universal D-Handle Router Base Plate For Compact Routers

Question 8

Is your 10 pc. Brass Template Guide Kit (BTG-100) compatible with router base set 115-046? View answer

Answer posted 7 years ago | Infinity Tools Universal D-Handle Router Base Plate For Compact Routers

Question 9

Do you have replacement blades for the Sprunger NJ600 jointer/planer, a 6” three-blade jointer? I’ve asked before. View answer

Answer posted 7 years ago | Infinity Tools High Speed Steel Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets

Question 10

What are the dimension for the inlay View answer

Answer posted 7 years ago | Infinity Tools Rose - Multi-Layer Inlay System

Question 11

Can I use your dust collection system on 220/240V machines, or must I use a regular 120V outlet? View answer

Answer posted 7 years ago | iVac 4-Pc. Auto Dust Collection Pack w/ 115 VAC Switch

Question 12

Hi - In which country are these planes made? View answer

Answer posted 7 years ago | Infinity Tools Wood Jointer Hand Plane

Question 13

Do you have an insert for the older right tilt unisaw? Model 34-450 View answer

Answer posted 7 years ago | Betterley Tru-Cut Insert System For Delta Right Tilt Unisaw

Question 14

I need the part numbers of your flush trim router bits that have a guide bearing diameter of .375 inch or less. View answer

Answer posted 7 years ago | Infinity Tools 1/4" Shank Flush Trim Router Bits w/ Downshear

Question 15

How can I automatically turn on a 1HP dust collector with my 220v/20A jointer planer combo? Is this possible? View answer

Answer posted 7 years ago | iVac 7-Pc. Auto Dust Collection Pack w/ 115 VAC Switch

Question 16

will 36-920 thru cut 3/4" stock? View answer

Answer posted 7 years ago | Infinity Tools 1/4" Shank Chamfer Router Bits

Question 17

Is the router base plate for this jig the same as the base plate for the circle cutting jig? View answer

Answer posted 7 years ago | Milescraft Design & Inlay Kit

Question 18

Do I need the Precision Miter Bar to use the Coping and Crosscut sled? Why does it not come with one? View answer

Answer posted 7 years ago | Infinity Tools Pro Coping Sled

Question 19

Can this plate be pre-drilled for a Porter-Cable 690? What are the extra holes for, and what type of screws are used? View answer

Answer posted 7 years ago | JessEm Rout-R-Plate

Question 20

Double checking that this will fit the ATF55E Festool track saw and the best choice for plywood? View answer

Answer posted 7 years ago | Infinity Tools 160mm x 48T x 20mm Bore Track Master Saw Blade

Question 21

Interested in the 8 Hock chef knife kit. What are the exact dimensions: total length, thickness, and width? View answer

Answer posted 7 years ago | Hock Tools 5" Chef's Knife Kit

Question 22

Will you ever make a shaker cutter for my cutter head? I wish you offered a fitting shaker blade. View answer

Answer posted 7 years ago | Kreg 90° Corner Clamp w/ Automax

Question 23

83-040 ogee cuttrerhead. Can I purchase just the ogee cutterhead and matching reverse cutterhead. View answer

Answer posted 7 years ago | Infinity Tools Interior & Exterior Door 2-Piece Shaper Cutter Sets, 3/4" Bore

Question 24

DO YOU MAKE YOUR RIP BLADES FOR BAND SAWS IN AN 80" ? WOULD LIKE TO HAVE AN INFINITY BLADE IF POSSIBLE. View answer

Answer posted 7 years ago | Infinity Tools Resaw Bandsaw Blades

Question 25

Will the replacement blades you sell fit my 15-year-old Jesada rail and style shaper head? The current blades are too thin to sharpen. View answer

Answer posted 7 years ago | Infinity Tools Combination Rail & Stile Shaper Cutter, 1-1/4" Bore

Question 26

Will the Router Table Dust Collector fit a Bosch RA1181 table and 1617 router? What hardware is needed? View answer

Answer posted 7 years ago | Milescraft Router Table Dust Collector

Question 27

Can Jessem Clear Cut Tablesaw Stock Guides be attached to a Delta Unifense? Is there a mounting kit? View answer

Answer posted 7 years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 28

Do these blades fit in a standard jewelers saw? View answer

Answer posted 7 years ago | Pegas #7 Skip Tooth Fret Saw Blades

Question 29

can these be re-sharpened View answer

Answer posted 7 years ago | Infinity Tools High Speed Steel Knives For DeWalt 734 Planer, 3-Pcs.

Question 30

Is the system a DIY install or does one need to have an electrician install? View answer

Answer posted 7 years ago | iVac 8-Pc. Auto Dust Collection w/ Contactor

Question 31

Hi I have an older Bosch plunge 3.25 hp 1615 EVS router, is my router compatible with the RTF-007? View answer

Answer posted 7 years ago | JessEm Rout-R-Lift Prestige for Plunge Based Routers

Question 32

101-631Bl Will the above blade fit a stanley bailey #3 (1 3/4 cutter) View answer

Answer posted 7 years ago | Infinity Tools Wood Smoothing Hand Plane

Question 33

What are the 2 yellow strips on the phenolic and what's their purpose? View answer

Answer posted 7 years ago | Infinity Tools HD Frame Master - For HD Frame Templates - Router Or Shaper

Question 34

Do you have a 30° Lock Miter Router Bit Set for a 6-sided project or another suitable router bit? View answer

Answer posted 7 years ago | Infinity Tools 1/2" Shank 22.5° Lock Miter Router Bit Set w/ Setup Block

Question 35

What exactly does this mean--Requires minimum 2.5 CFM @ 90 PSI View answer

Answer posted 7 years ago | Infinity Tools Venturi Vacuum System

Question 36

Do you sell the Leigh 5/16 straight bit for D4Pro jig without the whole set? View answer

Answer posted 7 years ago | Brocas para fresadora de cola de milano con vástago de 1/4" de Infinity Tools

Question 37

Do you carry any 96" bandsaw blades? If so, what widths and TPI View answer

Answer posted 7 years ago | Infinity Tools Resaw Bandsaw Blades

Question 38

Do the plugfones come with a guarantee? View answer

Answer posted 7 years ago | Plugfones - Liberate 2.0 Bluetooth Earplug Headphones

Question 39

is there a list or routers which this fits - specifically does it fit a Porter Cable 690 series View answer

Answer posted 7 years ago | MPOWER 3-Pc. CRB7 Router Base Complete Package

Question 40

for the 12" x 12" predrilled router base plate what is the thickness 1/4" or 3/8" View answer

Answer posted 7 years ago | Infinity Tools Universal 7.5" Router Base Plate

Question 41

Which bit would work better with 3/4 stock the sr. or jr. View answer

Answer posted 7 years ago | Infinity Tools 1/2" Shank Lock Miter Jr. Router Bit

Question 42

need speed control for my Titon TRA001 31/4 Router. Speed control # TRA027. Where or how can I get it. View answer

Answer posted 7 years ago | Triton 3-1/4 HP Dual Mode Precision Plunge Router (TRA001)

Question 43

I can't tell from the pictures. Is the sole square to the side thereby allowing use in a shooting board? View answer

Answer posted 7 years ago | Infinity Tools Wood Jack Hand Plane

Question 44

Is there a special clamp for attaching the guide to the underside of the workpiece? View answer

Answer posted 7 years ago | Kreg Accu-Cut and Rip-Cut Systems (KMA2685 & KMA2700)

Question 45

how do I add this item to my wish list? View answer

Answer posted 7 years ago | Infinity Tools Master Tapered Dovetail Spline System w/ Router Jigs, Spline Making Sled, 6 Dovetail Bits & 2 Brass Guides

Question 46

Will the clear cut table saw stock guides [ ts ] fit a desalt tablesaw [ dwe7491RS ] ? View answer

Answer posted 7 years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 47

What is the distance from the jig’s front edge to the miter bar? Min. and max. distance from miter channel to bit center? View answer

Answer posted 7 years ago | Infinity Tools Vertical Router Sled

Question 48

I'm interested in Item Number: 100-700C, can you change the font? View answer

Answer posted 7 years ago

Question 49

To make nested dovetails as shown in your video, what should I order? Are there other patterns available? View answer

Answer posted 7 years ago | Infinity Tools Master Tapered Dovetail Spline System w/ Router Jigs, Spline Making Sled, 6 Dovetail Bits & 2 Brass Guides

Question 50

What size bull nose bit do I need for 3/4 wood? View answer

Answer posted 7 years ago | Infinity Tools 1/2" Shank Bullnose Router Bits

Browse by Topic

Tools