Question 1

I have an older craftsman saw will it work on my saw and does this replace my fence or work with it View answer

Asked 6 ´years ago | Wixey 0" - 60" Digital Table Saw Fence Readout

Question 2

Do you have a plain ogee bit that matches your extended tenon ogee bit? Need it for a 2 1/2 door project. View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Interior & Exterior Door Router Bit Set

Question 3

Is the Festool Kapex KS 120 zero clearance insert listing correct? Do I need one or two plates for a complete set? View answer

Asked 6 ´years ago | Infinity Tools Festool Kapex KS 120 Miter Saw Z.C.I.

Question 4

What is the minimum horsepower router required for this cutter? Thanks! View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Raised Panel Router Bits w/ Backcutter

Question 5

Will this setup jig work with the Grizzly CT1712 Lock Miter bit? It isn’t listed in your documents. View answer

Asked 6 ´years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 6

Whats the thread size for the unit and the macro line fittings? View answer

Asked 6 ´years ago | Venturi Vacuum System

Question 7

What are the thread sizes for the unit and the macro line fittings? View answer

Asked 6 ´years ago | Infinity Tools 1.5" Vacuum Gauge w/ Brass Fitting, For Venturi System

Question 8

Does the 3 piece tapered counter sink set come with the drill bits? View answer

Asked 6 ´years ago | Make it Snappy Tools 3-Piece HSS Tapered Countersink Bit Set

Question 9

How well does this burn signatures? Will a tight signature burn too much and be unreadable? View answer

Asked 6 ´years ago

Question 10

Do you offer blade sharpening? View answer

Asked 6 ´years ago | Infinity Tools 10" x 50 Tooth Combination Table Saw Blade

Question 11

Does the RTL-003 come with an installation template? View answer

Asked 6 ´years ago | JessEm Mast-R-Lift II - 8-1/4" x 11-3/4" Aluminum Plate

Question 12

Do you have set up blocks for a tongue and groove router bit with a v notch? View answer

Asked 6 ´years ago | Infinity Tools Setup Block for 55-501 Glue Joint Bit

Question 13

Does the 12” Miter Max 90T blade have vibration-reducing cuts? What kerf do you recommend for SCMS with a 15A motor? View answer

Asked 6 ´years ago | Infinity Tools 12" Miter Saw Blade

Question 14

Will any of the Quick Change Chucks fit a Craftsman table router? I have model 320.37595 View answer

Asked 6 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 15

Do you grind custom raised panel knife inserts for for your shaper head? View answer

Asked 6 ´years ago | Infinity Tools Raised Panel Insert-Pro Shaper Cutters, 1-1/4" Bore

Question 16

For item #84-076, which bushings are right for a 1” spindle: #BUS-107 or #BUS-105? View answer

Asked 6 ´years ago | Infinity Tools 2-Pc. T-Bushing Set

Question 17

I would like to know if you have raised panel shaper with insert left & right hand sets View answer

Asked 6 ´years ago | Infinity Tools Cabinet Door Rail & Stile Shaper Cutter Sets, 3/4" Bore

Question 18

Do you have an 8” x 1/4” flat top saw blade for making box joints with a 1” (25.4mm) bore? View answer

Asked 6 ´years ago | Infinity Tools 8" Flat-Top Dado Saw Blade - 5/32" Kerf

Question 19

What size drill press will the Woodpecker drill press table and fence work with. Thanks for your help. View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Package w/ Essential Aluminum Fence

Question 20

Will this work with a shopsmith View answer

Asked 6 ´years ago | iGaging Digital Measuring Sets

Question 21

Are spare belts available for the ken onion sharpener. View answer

Asked 6 ´years ago | Work Sharp Knife & Tool Sharpener, Ken Onion Special Edition

Question 22

Will this work with Freud 99-035 Lock Miter Bit? View answer

Asked 6 ´years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 23

Do you have bushings to 3/4" spindle View answer

Asked 6 ´years ago | Infinity Tools Raised Panel Insert-Pro Shaper Cutters, 1-1/4" Bore

Question 24

Do you stock 7/16” and 7/8” bits for the 5-Pc. Extra Long Dowel & Plug Cutter Set? View answer

Asked 6 ´years ago | Infinity Tools 5-Pc. Extra Long Dowel & Plug Cutter Set

Question 25

WIll this table accept an Incra Wonder Fence? View answer

Asked 6 ´years ago | Infinity Tools Plycore Router Table Top, 24" x 32" x 1-1/8" Thick

Question 26

Does the 00-SSD include the metal disc for setting up a sanding disc on a 10” Craftsman table saw? View answer

Asked 6 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'

Question 27

Where can I find the Infinity 8” Flat-Top Dado Saw Blade (5/32”) in Canada? Amazon doesn’t have it. View answer

Asked 6 ´years ago | Infinity Tools 8" Flat-Top Dado Saw Blade - 5/32" Kerf

Question 28

what size fitting does the 5mm hose fit to (the thread end)? View answer

Asked 6 ´years ago | Venturi Vacuum System

Question 29

Can the feed direction of the rollers on your guide system be reversed for shapers? Are there plans for this feature? View answer

Asked 6 ´years ago | JessEm Clear-Cut Router Table Stock Guides

Question 30

Is the drawer lock router setup block suitable for other wood thicknesses or only specific sizes? View answer

Asked 6 ´years ago | Infinity Tools Setup Block for 55-501 Glue Joint Bit

Question 31

For the Craftsman 20” band saw model 112, are the cool blocks slotted with center mount screws and flatter than blocks? View answer

Asked 6 ´years ago | Cool Blocks For Bandsaw

Question 32

Is this Jessen Rout R II lift compatible with Craftsman model 320.27683? View answer

Asked 6 ´years ago | JessEm Rout-R-Lift II

Question 33

Can I get just the contractor foam replacement plugs and not the foam twisty kind? View answer

Asked 6 ´years ago | Plugfones Replacement Earplugs

Question 34

Will the RTI-DIY 5 pc. router insert plate template fit the Jessem Mast-R-Lift II without voids at the corners? View answer

Asked 6 ´years ago | Infinity Tools 5-Pc. Router Insert Plate Template Package

Question 35

What are the dimensions of portable paint tent ? View answer

Asked 6 ´years ago | HomeRight Portable Spray Booths

Question 36

Can I use a SCUBA tank with 140psi low pressure and 1/4 quick disconnect for this tool? View answer

Asked 6 ´years ago | Venturi Vacuum System

Question 37

Can the coping sled be adjusted (reconfigured) to accept 3"x3" stock? Thank you. View answer

Asked 6 ´years ago | Infinity Tools Vertical Router Sled

Question 38

Are these jigs compatible with wood line lock miter bits? Thank you View answer

Asked 6 ´years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 39

Do you make a ZCI for the 10” DW717 sliding miter saw, or know where I can find one? View answer

Asked 6 ´years ago | Infinity Tools Zero Clearance Insert (Z.C.I.) Plate for DeWalt 10" & 12" Non-Sliding Saws

Question 40

Are the non-slip pads replaceable? View answer

Asked 6 ´years ago | MicroJIG GRR-RIP Smart Hook Push Block

Question 41

52-506 item # is this a bottom cleaning bit? View answer

Asked 6 ´years ago | Infinity Tools 1/4" Shank Dado Router Bit

Question 42

In what country is this gauge manufactured? View answer

Asked 6 ´years ago | iGaging Wheel Marking, Mortise & Depth Gauge

Question 43

How long of a tongue does it cut? Looking for 1/2" tongue on Standard profile. Thanks- Greg View answer

Asked 6 ´years ago | Infinity Tools Raised Panel Shaper Cutter

Question 44

Is it possible to use the chipper blades alone to cut a 3/16 inch groove? View answer

Asked 6 ´years ago | Infinity Tools Dadonator Jr., 6" Stacked Dado Saw Blade Set, 5/8" Bore

Question 45

Will these work for a 14" bandsaw from Harbor Freight? View answer

Asked 6 ´years ago | Cool Blocks For Bandsaw

Question 46

I would like a complete package deal with 27 x 43 table and Triton router, stand and wheels with foot lift. View answer

Asked 6 ´years ago | Infinity Tools Pro Router Table Package with Cast Iron Top & JessEm Mast-R-Lift (02120)

Question 47

What is the thickness of each rule in the 4 rule set? Thank you. View answer

Asked 6 ´years ago | iGaging 4R Rule

Question 48

With 8 blast gates connected, will only the active tool’s gate open, or will all gates open? View answer

Asked 6 ´years ago | iVac 4" Fully Automated Pro Blast Gate

Question 49

Hi - I am looking for replacement knives for a Ridgid jointer jp06000. Do you sell them? View answer

Asked 6 ´years ago | Infinity Tools Carbide Tipped Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets

Question 50

Do you have a set up block that will fit the Amana Tool #55387 Drawer lock router bit. Thank you. View answer

Asked 6 ´years ago | Infinity Tools Setup Block for 55-501 Glue Joint Bit

Browse by Topic

Tools