Question 1

Are these blades Saw Stop compatible? View answer

Asked 6 ´years ago | Infinity Tools 4-Pc Thin Kerf Table Saw Blade Package, With 6" Dadonator Jr. Saw Blade Set, 5/8" Bore

Question 2

Can the 27 x 47 table saw router table top be configured to run alongtheu 47 inch side View answer

Asked 6 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 3

I?m replacing a window stool in a 1900 schoolhouse. Will the 54-504 bit give a full bullnose on 1 1/8? material? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Bullnose Router Bits

Question 4

Does the Express come with a fence? If so what size? Does it come with the stop block? Thanks. View answer

Asked 6 ´years ago | INCRA Miter EXPRESS

Question 5

For bowties thicker than 7/16”, do you have a recommended setup even though this set is not for deeper cuts? View answer

Asked 6 ´years ago | Infinity Tools Nested Butterfly - Multi-Layer Inlay System

Question 6

Could this jig accommodate a 28" table leg taper? View answer

Asked 6 ´years ago | MicroJIG Microdial Tapering Jig - Table Saw & Router Table

Question 7

I need HSS replacement knives for Robland XSD-31: 310mm x 25mm x 3mm. Can you recommend a part number? View answer

Asked 6 ´years ago | Infinity Tools High Speed Steel Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets

Question 8

Any setup tips for using the glue joint shaper cutter? I’m struggling with trial and error. View answer

Asked 6 ´years ago | Infinity Tools Reverse Glue Joint Shape-Up Shaper Cutter, 3/4" Bore

Question 9

my router base has a 1-5/8 in. opening will the brass inlay work View answer

Asked 6 ´years ago | Infinity Tools Brass Inlay Kit w/ Spiral Bit & Centering Pin

Question 10

Does the Jessem lift fit in a Kreg router table without major adjustments. View answer

Asked 6 ´years ago | JessEm Rout-R-Lift Prestige for Plunge Based Routers

Question 11

What base material is used now? Is it the new or older material compared to previous versions? View answer

Asked 6 ´years ago | MPOWER Combination Router Base

Question 12

For the 3-piece pro door set with a 3/4” spindle, should I use the tall bushing in the stile middle? View answer

Asked 6 ´years ago | Infinity Tools 2-Pc. T-Bushing Set

Question 13

can you make an iron in "œSpring Cleaning" font ? 10 letters and a space. "œSAILOR RUSS" View answer

Asked 6 ´years ago

Question 14

Will you customize the saw blade to fit a Hammer (Felder) sliding table saw? View answer

Asked 6 ´years ago | Infinity Tools 10" Laser Kerf Saw Blade & Splitter, 5/8" Arbor

Question 15

Would the 27” x 29” Table Saw Router Table Package be compatible with the Delta 36-725 Table Saw? View answer

Asked 6 ´years ago | Infinity Tools Table Saw Router Table Package w/ 27" x 29" Table Top & 3.25HP Triton Router (TRA001)

Question 16

Will this unit fit DeWalt DWE7490,DWE7491 Heavy -Duty 10" Job Site Table Saws? Thanks. View answer

Asked 6 ´years ago | Milescraft Table Saw Dust Collector - Dust Cutter

Question 17

What type of metal is the insert pro rabbeting cutter head made of # 84-076 View answer

Asked 6 ´years ago | Infinity Tools Insert-Pro Rabbeting Shaper Cutter, 1-1/4" Bore

Question 18

Do you have dust collection hoses longer than 10'? View answer

Asked 6 ´years ago | Anti-Static PVC Dust Collection Hose, 10 Feet.

Question 19

Your pictures show an electric iron and a non-electric. How do I know which one I am ordering? View answer

Asked 6 ´years ago

Question 20

Does the baseplate fit on a Chicago Electric 1 1/2 HP Plunge Router which I purchased at Harbor Freight? View answer

Asked 6 ´years ago | Milescraft SignPro Kit

Question 21

Have had the Wizard several years, but now can't find owner's manual or charger. Where can I find replacements? View answer

Asked 6 ´years ago | Lumber Wizard 5 - Laser Line Woodworking Metal Detector

Question 22

I have a Woodpeckers super fence. Will these work on this fence or is it to tall? The fence is 3 7/8 inches tall. View answer

Asked 6 ´years ago | JessEm Clear-Cut Router Table Stock Guides

Question 23

I need a base plate with a 1 3/16" center hole for guide bushings for my Triton router. It has four screws. Will your plates fit? View answer

Asked 6 ´years ago | Infinity Tools Universal 7.5" Router Base Plate

Question 24

Can I use a 5 pad on a 6 Mirka Deros sander, or do I need to purchase a 6 kit? The 6 model is 220V in Europe. View answer

Asked 6 ´years ago | Mirka Deros Dust-Free Sanding System with 18' Coaxial Vacuum Hose

Question 25

do you sell a set up block for the #91-522A interior & exterior door router bit set? View answer

Asked 6 ´years ago | Bloque de configuración de Infinity Tools para broca para juntas encoladas 55-501

Question 26

What brand of routers can be fitted to the PRTF100 version View answer

Asked 6 ´years ago | Infinity Tools Pro Router Table Package with Triton 3-1/4 HP Router (TRA001)

Question 27

I have Powermatic Accu-Fence will this work on it. View answer

Asked 6 ´years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 28

My tools and vacuum are 220 volts. Is a contactor necessary for the system? If so, will it work on a 220V system? View answer

Asked 6 ´years ago | iVac 8-Pc. Auto Dust Collection w/ Contactor

Question 29

Will this inlay kit work well and accurately with end grain material for making butcher blocks? View answer

Asked 6 ´years ago | Infinity Tools Multi-Layer Inlay System Accessory Package

Question 30

Which collete sleeve (part #) would go with with the Duwalt 616-618 router eliminator quick changer? View answer

Asked 6 ´years ago | Infinity Tools 8mm x 1/2" x 1-1/4" Router Collet Reducing Sleeve

Question 31

Can I use this on the Dewalt 735 planer? Will I need to do any adjustments afterwards? View answer

Asked 6 ´years ago | Infinity Tools Diamond Knife Hone For HSS & Carbide Planer & Jointer Knives

Question 32

Can you identify the router bits I need if I send you a picture of my door? I don't see an upload option. View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Matched Rail & Stile Router Bits w/ Setup Block

Question 33

How far are the T tracks from edge of table? View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 34

I need 1/2” deep dados in 1” PVC trim for porch molding. Can a template for my plunge router handle this, and what products fit this need? View answer

Asked 6 ´years ago | Infinity Tools 2-Pc. Downcut Spiral Set For Plywood Dado Cuts

Question 35

Where are your blades made? View answer

Asked 6 ´years ago | Narex 4-Pc. Spoon Carving Starter Set

Question 36

what is diameter of 1/8 in spiral bit [100-198] ie does it fit in 1/4 in router? View answer

Asked 6 ´years ago | Infinity Tools Multi-Layer Inlay System Accessory Package

Question 37

will your item #8301 cut Mahogany 3/4 for raised panels satisfaction View answer

Asked 6 ´years ago | Infinity Tools Raised Panel Shaper Cutter

Question 38

Do you have the Knew Concepts Coping Saw 101-625 and Pegasus 18tpi blades with pins? Is curbside pickup available? View answer

Asked 6 ´years ago | Knew Concepts 6.5" Coping Saw

Question 39

What is the vacuum hose connection size? Will it fit my Festool and Fein dust collectors? How long is the cord? View answer

Asked 6 ´years ago | Mirka DEROS 5" Orbit Finish Sander Vacuum Ready w/ Case

Question 40

I need a bit for a 78 radius curve on a 3 thick maple top. What bit should I use with a plywood pattern? View answer

Asked 6 ´years ago | Infinity Tools 1/4" Shank Straight Router Bit w/ Top Bearing

Question 41

What are the ingredients? View answer

Asked 6 ´years ago | Odie's Oil Food Safe Wood Finish - 9 oz. Jar

Question 42

Do you have a video for setup and calibration? Is the hose clamp method recommended for mounting? View answer

Asked 6 ´years ago | Wixey Drill Press Precision Laser Guide

Question 43

is it possible to order just the digital readout portion as a replacement part? View answer

Asked 6 ´years ago | iGaging 6" Digital Height Gauge

Question 44

Does the Infinity Tools router table insert fit the SawStop RT-FS table? Do the holes align properly? View answer

Asked 6 ´years ago | INCRA Miter 1000SE with 18" to 31" Fence & Flip Stop

Question 45

How does this dust collection system hook to the saw? View answer

Asked 6 ´years ago | Milescraft Table Saw Dust Collector - Dust Cutter

Question 46

I have a porter cable 75182 router and need both collet wrenches, do you sell them? View answer

Asked 6 ´years ago | Infinity Tools Router Collet Offset Wrench For Porter Cable 1-1/8"

Question 47

Is a contactor necessary for your dust collector system? Can I connect 220V and 110V tools to turn the vacuum on/off? View answer

Asked 6 ´years ago | iVac 8-Pc. Auto Dust Collection w/ Contactor

Question 48

Are Lock Mitre Master Jigs available in the UK? If yes, what is the shipping cost? View answer

Asked 6 ´years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 49

Asked 6 ´years ago | Infinity Tools 1/2" Shank Picture & Frame Making Router Bits

Question 50

I need an Incra Box Jig for a SawStop saw. Do you sell a plastic version for safety reasons? View answer

Asked 6 ´years ago | INCRA I-BOX - Box Joint Jig For Table Saw & Router Table

Browse by Topic

Tools