Question 1

Is the coverage rate for General Finishes Arm-R-Seal Topcoat 400-500 sq ft per gallon for one coat or three coats? View answer

Answer posted 6 years ago | General Finishes Arm-R-Seal Topcoat

Question 2

Will this work with 5/8” PVC for column trim bases? The old joints used something similar. View answer

Answer posted 6 years ago | Infinity Tools 1/2" Shank Lapped Miter Joint Router Bit Set w/ 3/4" Setup Block

Question 3

DO YOU CARRY THE JESSEM 02312 MODEL FOR THE HITACHI ROUTERS? View answer

Answer posted 6 years ago | JessEm Rout-R-Lift II

Question 4

do they make a planer bit for a 1/4 in. shank router. View answer

Answer posted 6 years ago | Infinity Tools 1/4" Shank Dado Router Bit

Question 5

Can this be set up to make repeatable dado cuts? View answer

Answer posted 6 years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 6

What size router bit wrench is required to tighten the collet extension? View answer

Answer posted 6 years ago | Infinity Tools Router Bit Collet Extension

Question 7

Was is the O. D. (outer diameter) of the two ends? View answer

Answer posted 6 years ago | Infinity Tools 4" Splice

Question 8

I have a Makita M3600G, Does this system fit that router? View answer

Answer posted 6 years ago | MPOWER 3-Pc. CRB7 Router Base Complete Package

Question 9

Do you have a recommended minimum horsepower rating for the 52-506 mega dado bit? View answer

Answer posted 6 years ago | Infinity Tools 1/4" Shank Dado Router Bit

Question 10

Does this dust collection system come with hose ? View answer

Answer posted 6 years ago | RIKON 1 HP Dust Collector w/ 5 Micron Bag

Question 11

What are the thicknesses of your saws? I need to cut grooves in a fretboard for fretwire. View answer

Answer posted 6 years ago | Shark Corp. 5-Pc Master Woodworker's Saw Set

Question 12

Do you sell individual grinder belts for the Ken Onion blade grinder attachment? Specifically, the ultra coarse and fine belts? View answer

Answer posted 6 years ago | Work Sharp Ken Onion 5-Pc. Blade Grinder Attachment Belt Kit

Question 13

51-502B what is the overall length of this bit please? View answer

Answer posted 6 years ago | Infinity Tools 1/4" Shank Bowl & Tray Router Bits

Question 14

What is the thickness of these Rub Collars; RUB 100, RUB 101, RUB 102, RUB 107. View answer

Answer posted 6 years ago | Infinity Tools Rub Collar for Shape-Up Shaper Cutters

Question 15

My newer portable Craftsman table saw has a 5/8" wide non-standard miter slot. Will your miter guide fit? View answer

Answer posted 6 years ago | Infinity Tools Thin-Rip Guide For Table Saw, Bandsaw & Router Table

Question 16

How thick of a table top does the Armor Tools Horizontal Dog Clamp need to be secure? Will 3/4” thick dog holes work? View answer

Answer posted 6 years ago | BORA Self Adjusting Horizontal Dog Clamp

Question 17

Will this work with Porter Cable 450PK View answer

Answer posted 6 years ago | Cortador de círculos y ovalados con base de vacío Infinity Tools

Question 18

Will this fit a LS1018? View answer

Answer posted 6 years ago | Wooster White China Bristle 2"

Question 19

Is there a recommended torque setting for seating the screws? (I have read the instructions.) View answer

Answer posted 6 years ago | Infinity Tools Raised Panel Insert-Pro Shaper Cutters, 1-1/4" Bore

Question 20

Can it cut thicker than 1/8"? View answer

Answer posted 6 years ago | MicroJIG GRR-Ripper 1/8" Thin-Stock Accessory

Question 21

will these work on a 3/4 spindle shaper. View answer

Answer posted 6 years ago | Infinity Tools Raised Panel Insert-Pro Shaper Cutters, 1-1/4" Bore

Question 22

When using this tool - do you need to reset/ relevel the outfeed table? Diamond knife hone for jointer DKH-002 View answer

Answer posted 6 years ago | Infinity Tools Diamond Knife Hone For HSS & Carbide Planer & Jointer Knives

Question 23

Does this include the sled? Little confusing. View answer

Answer posted 6 years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 24

Is the 101-739 12mm Narex wood rasp the same diameter along its full length? View answer

Answer posted 6 years ago | Narex Full Round Rasp - 6mm diameter, 20 teeth/cm

Question 25

What is the country of origin of the Grace three plier set? View answer

Answer posted 6 years ago | GRACE USA 3-Pc. Precision Plier Set

Question 26

Need a zero clearance insert for Dewalt DWS709. Is the DWS708 insert compatible? View answer

Answer posted 6 years ago | Infinity Tools Zero Clearance Insert (Z.C.I.) Plate for DeWalt 10" & 12" Non-Sliding Saws

Question 27

Is there an attachment for the 48" to be turned into a 96" track? View answer

Answer posted 6 years ago | Kreg Accu-Cut and Rip-Cut Systems (KMA2685 & KMA2700)

Question 28

Are these suitable for cutting acrylic with a PC 3.25hp? View answer

Answer posted 6 years ago | Infinity Tools 1/2" Shank Mega Flush Trim Router Bits

Question 29

You sell the locking ring set, but do you sell the locking ring wrench separately? View answer

Answer posted 6 years ago | JessEm Rout-R-Plate

Question 30

This looks great! Any way to do 3/4" dados I. One pass? View answer

Answer posted 6 years ago | Infinity Tools Precision Router Dado Jig

Question 31

Will this jig work on the Freud miter lock bit 99-035? View answer

Answer posted 6 years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 32

I need to cut tongue and groove on maple flooring but can't get the router bit low enough. Any solutions? View answer

Answer posted 6 years ago | Infinity Tools 1/2" Shank Floor Making Router Bit Sets

Question 33

What’s the bearing for on the stile bit if the workpiece is below it? Also, why does it bounce into the fence? View answer

Answer posted 6 years ago | Infinity Tools 1/2" Shank 3-Pc. Ultimate Glass Door Making Router Bit Set

Question 34

Will your replacement slide (PDJ-SLD) fit into Emerson Straight-Edge Clamps (C24, C36, C50) clamp tracks? View answer

Answer posted 6 years ago | Infinity Tools Precision Router Dado Jig

Question 35

Is this 2.5" inside diameter or outside diameter? View answer

Answer posted 6 years ago | Manguera de recolección de polvo de PVC antiestática, 10 pies.

Question 36

Is the base pre-drilled to fit the Triton TRA001 and your 115-039 self-centering kit with roller bearings? View answer

Answer posted 6 years ago | Infinity Tools Universal 7.5" Router Base Plate

Question 37

What's the difference between "modern" and "traditional" shaker passage door sets? View answer

Answer posted 6 years ago

Question 38

Do you carry the 02314 model of this lift-II for the Rigid 29302 router. View answer

Answer posted 6 years ago | JessEm Rout-R-Lift II

Question 39

Can the Center Holding Jig work with 1/2" inch diameter stock? View answer

Answer posted 6 years ago | Infinity Tools Center Holding Jig For Drill Press

Question 40

will the 24 " grip and fence work on 10" bench top band saw View answer

Answer posted 6 years ago | Abrazaderas de borde recto Pro-Grip de 2" de ancho de Infinity Tools

Question 41

Do the JessEm guides come as a pair, or do I need to order two? View answer

Answer posted 6 years ago | JessEm Clear-Cut Router Table Stock Guides

Question 42

Do you have a circular blade protector for 16" blades or offer custom ones? View answer

Answer posted 6 years ago | Infinity Tools 8" Saw Blade Protector

Question 43

Do you have an insert for an older 8" Sears & Roebuck bench saw, model # 103.24241, p.n. 43712? View answer

Answer posted 6 years ago | Betterley Tru-Cut Insert System For Delta Right Tilt Unisaw

Question 44

Festool 2200,will it work for this router???? Please View answer

Answer posted 6 years ago | Infinity Tools Universal 7.5" Router Base Plate

Question 45

Does the Triton included in this package elevate enough to allow bit changes above the table ? View answer

Answer posted 6 years ago | Infinity Tools Pro Router Table Package with Triton 3-1/4 HP Router (TRA001)

Question 46

How thin of a cut can I take on the rip? I cut shaker box bands and need to go as thin as .06 to .068 Thank You View answer

Answer posted 6 years ago | Infinity Tools Thin-Rip Guide For Table Saw, Bandsaw & Router Table

Question 47

What is the distance from rear table edge to the sacrificial insert, and what is the insert size? View answer

Answer posted 6 years ago | Infinity Tools Drill Press Table Packages

Question 48

Good morning, can you give me the od for your SC-002 1/4" stop collar............Larry View answer

Answer posted 6 years ago | Infinity Tools Stop Collar for 1/2" Shank Bit With Align Key

Question 49

does the lock mitre set up jig work with the shaper cutter as well or just the router bit cutter? View answer

Answer posted 6 years ago | Infinity Tools Shape-Up 45° Lock Miter Shaper Cutter, 3/4" Bore

Question 50

I have a 40” x 78” tabletop. Can I use this base with slight modifications? I like its look and proportions. View answer

Answer posted 6 years ago | Base for Live-Edge Slab Table Plans

Browse by Topic

Tools