Question 1

I need the 83-034 bevel cutters in an 1 1/4" bore. Available ? View answer

Asked 7 ´years ago | Infinity Tools Cabinet Door Rail & Stile Shaper Cutter Sets, 3/4" Bore

Question 2

Is the mission available with a 1/4” cut instead of 5.5mm? Is the shaker available with a 1/2” cut instead of 3/8”? View answer

Asked 6 ´years ago | Infinity Tools Cabinet Door Rail & Stile Shaper Cutter Sets, 3/4" Bore

Question 3

Do you have a shaker style shaper cutter for 3/4 material ? View answer

Asked 7 ´years ago | Infinity Tools Interior & Exterior Door 2-Piece Shaper Cutter Sets, 3/4" Bore

Question 4

For bit 90-506, what is the length of the 1/4” flat profile from inside the rail to where the bevel starts? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Horizontal Raised Panel Router Bits

Question 5

What is the minimum horsepower router required for this cutter? Thanks! View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Raised Panel Router Bits w/ Backcutter

Question 6

Is the 90-507 ogee bit available without the back cutter View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Raised Panel Router Bits w/ Backcutter

Question 7

What size is the shank on your rosette cutters? View answer

Asked 7 ´years ago | Infinity Tools Carbide Tipped Rosette Cutters, 2-1/8" Diameter

Question 8

What is the diameter of the drive shaft on the RCH-105? View answer

Asked 6 ´years ago | Infinity Tools Carbide Tipped Rosette Cutters, 2-3/4"" Diameter

Question 9

Re round nose router bits 14-190 and 14-690. Are they carbide tipped it solid carbide or HSS View answer

Asked 6 ´years ago | Infinity Tools 1/4" Shank Roundnose Router Bits

Question 10

Does Whiteside make your roundover router bits ? View answer

Asked 7 ´years ago | Infinity Tools 1/4" Shank Roundover & Beading Router Bits

Question 11

will bearing BR-118 wok with router bit 23-140B and will that give me a 1/4 inch depth of cut View answer

Asked 7 ´years ago | Infinity Tools Slot Cutter w/ 1/4" Shank Arbor

Question 12

Could you make a biscuit cutter for a number 11 biscuit View answer

Asked 6 ´years ago | Infinity Tools 3-Wing Slot Cutter, 5/16" I.D. x 1-7/8" O.D.

Question 13

Can you tell me where are your router bits made, particularly these spiral bits? View answer

Asked 6 ´years ago | Infinity Tools 1/4" Shank x 1/4" Cutter Diameter x 1" Cutter Length. Solid Carbide Spiral Flush Trim Router Bits

Question 14

What does Leigh #160 in you router bit notes mean? View answer

Asked 6 ´years ago | Infinity Tools 1/4" Shank Straight Router Bits

Question 15

In what country are these manufactured? View answer

Asked 6 ´years ago | Infinity Tools 1/4" Shank Straight Router Bits w/ Plunge Point

Question 16

Can you tell me what is in item #00-SSD? View answer

Asked 6 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'

Question 17

Will this work on my Craftsman table saw? View answer

Asked 7 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'

Question 18

Do you have higher grit sanding discs for the 'tablesaw setup and sanding disk'? Looking for over 300 grit. View answer

Asked 7 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'

Question 19

Is this Table Saw Setup and Sanding Disk available with a 30mm bore for my Minimax C26 table saw? View answer

Asked 7 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'

Question 20

Is this disk available for a 9 inch Rockwell xxxx table saw? View answer

Asked 6 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'

Question 21

does this come in a 7.25 dia.? View answer

Asked 6 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'

Question 22

What is the difference between SSD-010 and 00-SSD? View answer

Asked 7 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'

Question 23

What sand paper grits and how many sheets are included in the 00-SSD package? View answer

Asked 6 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'

Question 24

Where is the Table Saw Setup and Sanding Disc made? View answer

Asked 6 ´years ago | Klingspor 10" Sanding Disk w/ 5/8" Arbor'

Question 25

How do we get this glue out of my husband's shirt? View answer

Asked 7 ´years ago | Titebond III Ultimate Wood Glue

Question 26

Will treating wood with minwax stain effect the holding power of Tilebond Ultimate wood glue View answer

Asked 7 ´years ago | Titebond III Ultimate Wood Glue

Question 27

Where can I buy infinity tools products in Argentina, for example titebond? View answer

Asked 6 ´years ago | Titebond Original Wood Glue

Question 28

Im interested in the V tongue and groove router bit set 61-504. Does this set have carbide cutters? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank 2-Pc. V-Tongue & Groove Router Bit Set

Question 29

what bit do you recommend to use with a dado template in plywood { 3/4" shelf x 3/8" deep} Thanks View answer

Asked 7 ´years ago | Infinity Tools 1/4" Shank Straight Router Bit w/ Top Bearing

Question 30

Are these bits three cutting edges or two? View answer

Asked 6 ´years ago | Infinity Tools 1/4" Shank Straight Router Bit w/ Top Bearing

Question 31

do you have this triple bead and triple flute set in 1/4 shank? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Triple Flute & Bead Router Bits

Question 32

Do you make a 4 bead router bit? I'm wanting to replace some trim work on an antique cedar chest? View answer

Asked 6 ´years ago | Infinity Tools 1/2" Shank Triple Flute & Bead Router Bits

Question 33

In your window sash sets (SR. and Jr.), is ogee the only profile available? Old sashes in New England have a bead. View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Window Sash Router Bit Sets

Question 34

Is the Jr set, 55-802, carbide tipped? View answer

Asked 7 ´years ago | Infinity Tools 1/2" Shank Window Sash Router Bit Sets

Question 35

What are the distances between the T-tracks? View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 36

What exactly is included with the DPT203? View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 37

I need the diameter of the fence knobs and the fence height, aside from the 17” OC track distance. View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 38

Where is the drill press table system made View answer

Asked 6 ´years ago | Infinity Tools Drill Press Table Packages

Question 39

Where can I find detailed instructions sheets for this inlay? Multi Layer Inlay System - 4" Compass Rose View answer

Asked 6 ´years ago | Infinity Tools Multi Layer Inlay System - 4" Compass Rose

Question 40

Could this be safely used on a General Shaper? View answer

Asked 6 ´years ago | Infinity Tools Mini Power Feeder For Router Table & Shapers

Question 41

What speeds to you recommend running the feeder at, I have a 3hp router. View answer

Asked 6 ´years ago | Infinity Tools Mini Power Feeder For Router Table & Shapers

Question 42

Will the mini power feeder fit on an INCRA ROUTER FENCE ? View answer

Asked 7 ´years ago | Infinity Tools Mini Power Feeder For Router Table & Shapers

Question 43

Is your mini powerfeeder strong enough for feeding raised panels through the router table? View answer

Asked 6 ´years ago | Infinity Tools Mini Power Feeder For Router Table & Shapers

Question 44

Will this work on a festool router table View answer

Asked 6 ´years ago | Infinity Tools Mini Power Feeder For Router Table & Shapers

Question 45

How long is the warranty on the power feeder? View answer

Asked 7 ´years ago | Infinity Tools Mini Power Feeder For Router Table & Shapers

Question 46

Do you have this feeder in 220-240 V and 50 hz or with a CC motor? View answer

Asked 6 ´years ago | Infinity Tools Mini Power Feeder For Router Table & Shapers

Question 47

The power feeder operates in both directions. Does that mean that you can safely climb cut on a router table? View answer

Asked 6 ´years ago | Infinity Tools Mini Power Feeder For Router Table & Shapers

Question 48

I usually make thin moldings, will this feeder feed square stock that is 3/8 ? View answer

Asked 6 ´years ago | Infinity Tools Mini Power Feeder For Router Table & Shapers

Question 49

Are these sharpening stones8 x 2 3/4" or 3" wide View answer

Asked 6 ´years ago | Pride Abrasives Waterstone

Question 50

Will the table top work with a Craftsman table saw? If so how does it attach? View answer

Asked 6 ´years ago | Infinity Tools Table Saw Router Table Package w/ 27" x 29" Table Top & 3.25HP Triton Router (TRA001)

Browse by Topic

Tools