Question 1

I have the jointer with 6 inch 3/4 1/8 knives do you have any proposal for that? View answer

Answer posted 7 years ago | Infinity Tools High Speed Steel Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets

Question 2

I have a Ridgid 4512 Cast iron table saw, which insert fits this model? View answer

Answer posted 7 years ago | Betterley Tru-Cut Insert System For Delta Right Tilt Unisaw

Question 3

For bit 90-506, what is the length of the 1/4” flat profile from inside the rail to where the bevel starts? View answer

Answer posted 7 years ago | Infinity Tools 1/2" Shank Horizontal Raised Panel Router Bits

Question 4

Does the 10-Pc. TAB-LOCK Ring Insert Set include an insert for Porter Cable bushings? I have a Jessem router lift. View answer

Answer posted 7 years ago | Placa de inserción para mesa de fresado de aluminio de Infinity Tools, 9-1/4" x 11-3/4"

Question 5

I have a jig for a 1/2” lumber but need it for 5/8” ply. How should I position the gauge? View answer

Answer posted 7 years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 6

I have an Inca (Swiss made) 10-1/4" planer joiner! l would like a set of carbide knives for it! View answer

Answer posted 7 years ago | Infinity Tools Carbide Tipped Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets

Question 7

I need to edge glue 1X6 with a 1X8 spruce, I purchased titebond III ultimate. Is that a good choice? View answer

Answer posted 7 years ago | Titebond III Ultimate Wood Glue

Question 8

What is the weight of the Jointer Plane? View answer

Answer posted 7 years ago | Infinity Tools Wood Jointer Hand Plane

Question 9

Does this package come with an offset wrench for changing bits without having to lift t the router? View answer

Answer posted 7 years ago | Infinity Tools Pro Router Table Package with Triton 3-1/4 HP Router (TRA001)

Question 10

How do I know if my rigid table saw has the 7/16 or the 3/32 plate. View answer

Answer posted 7 years ago | Betterley Tru-Cut Insert System For Delta Right Tilt Unisaw

Question 11

Can I buy the 36" fence and brackets separately for the Magswitch work holding starter kit? Do you have a taller fence? View answer

Answer posted 7 years ago | Magswitch 18" Universal T-Track Fence

Question 12

Can you supply raised panel cutter, back cutter and proper rub collar without the stile & rail cutters? View answer

Answer posted 7 years ago | Infinity Tools 3-Pc. Cabinet Door Shape-Up Shaper Cutter Sets

Question 13

I need 12" chop saw blade that can cut 1/4 wall 4Ã—4 steal tubs View answer

Answer posted 7 years ago | Infinity Tools 12" Miter Saw Blade

Question 14

Does the LMM-002 jig work with the Jesada 655-502 lock miter bit? I’ve struggled using it properly. View answer

Answer posted 7 years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 15

Is this the new CRB7MK3 kit or an older version? My Dewalt DWP611 router needs the newest CRB7 version. View answer

Answer posted 7 years ago | MPOWER 3-Pc. CRB7 Router Base Complete Package

Question 16

Looking for a 3” mortising bit with a 1/2” shank. Do you have wider options? Thanks, and have a great day! View answer

Answer posted 7 years ago | Infinity Tools 1/4" Shank Mortise & Tenon Router Bits

Question 17

Hi - I've set up the dovetail spline sled. Any tips on making the first cut into the sled? View answer

Answer posted 7 years ago | Infinity Tools Master Tapered Dovetail Spline System w/ Router Jigs, Spline Making Sled, 6 Dovetail Bits & 2 Brass Guides

Question 18

does it accept both 1/2'' and 1/4'' shank? View answer

Answer posted 7 years ago | Triton 3-1/4 HP Dual Mode Precision Plunge Router (TRA001)

Question 19

Does the RTL-002 fit within the Rockler "œbucket boss" dust collection enclosure ? View answer

Answer posted 7 years ago | JessEm Mast-R-Lift II - Placa de aluminio de 8-1/4" x 11-3/4"

Question 20

Is there a Tru-Cut Table Saw Insert System for the Dewalt DWE7491RS 10-inch jobsite table saw? View answer

Answer posted 7 years ago | Betterley Tru-Cut Insert System For Delta Right Tilt Unisaw

Question 21

Can the bit #50-002 be adjusted to cut a t-slot slightly deeper and wider on my router table? View answer

Answer posted 7 years ago | Infinity Tools T-Slot, Channel & Hinge Router Bits

Question 22

What is this made of? View answer

Answer posted 7 years ago | FastCap Miter Saw Safety Stick

Question 23

What is the internal diameter of this product? Will it fit two solid pieces with a 2.5” OD? View answer

Answer posted 7 years ago | Infinity Tools 2-1/2" Splice

Question 24

Looking for an Ogee bit similar to the 56-517 profile in the American Woodworker book. Is this one yours? View answer

Answer posted 7 years ago | Infinity Tools 1/2" Shank Picture & Frame Making Router Bits

Question 25

Will the 50" straight edge clamp span a 4 ft wide plywood piece, considering clamp and stop space? View answer

Answer posted 7 years ago | Infinity Tools 2" Wide Pro-Grip Straight Edge Clamps

Question 26

Will this jig fit my Bosch TS 3000 table saw? Is the 1/4” flattop blade for 1/4” box joint dados? View answer

Answer posted 7 years ago | Infinity Tools Box Joint Jig Package with 1/4" Kerf Flat Top Blade and Setup Block Kit

Question 27

Can the 90-degree Corner Clamp hold two 3/4" pieces? Specs say 1" capacity; is that for each piece? View answer

Answer posted 7 years ago | Abrazadera de esquina de 90° Kreg con Automax

Question 28

Is it possible to add a backer board, to prevent tear out? Will the flip stop still work with a backer board? View answer

Answer posted 7 years ago | INCRA Miter 1000HD - 180 AngleLOCK Stops

Question 29

wll it fit on a powermatic model 63,10 View answer

Answer posted 7 years ago | Milescraft Table Saw Dust Collector - Dust Cutter

Question 30

I am needing a traditional cutter set to make interior doors. All I see on your site is Ogee. View answer

Answer posted 7 years ago | Infinity Tools Interior & Exterior Door 2-Piece Shaper Cutter Sets, 3/4" Bore

Question 31

Does it comes with storage case? View answer

Answer posted 7 years ago | iGaging 3-in-1 Digital Marking & Mortise Gauge

Question 32

Which plate should I order for a newer Ridgid R4512? I currently use a Leecraft Model RG-5 and need guidance. View answer

Answer posted 7 years ago | Betterley Tru-Cut Insert System For Delta Right Tilt Unisaw

Question 33

What is the name of the background music from Beautiful World about tasting colors? View answer

Answer posted 7 years ago | Narex Hand Stitched Rotary Rasp

Question 34

Will your LMM - 002 jig fit the Skil 91703 bit. View answer

Answer posted 7 years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 35

Looking to buy replacement feathers for 6 (#70014-01) and 10 (GP7) GuidePRO Band Saw Feed Guides. Do you sell them? View answer

Answer posted 7 years ago | BOW Products GuidePRO Resaw Featherboard for Bandsaws

Question 36

Do the round rings sit level with the insert plate top - when the rings are seated in place? View answer

Answer posted 7 years ago | Placa de inserción para mesa de fresado de aluminio de Infinity Tools, 9-1/4" x 11-3/4"

Question 37

Can rip cuts be performed often and as well as crosscuts View answer

Answer posted 7 years ago | Infinity Tools 10" x 50T Combination Tablesaw Blades, 5/8" Bore

Question 38

Will treating wood with minwax stain effect the holding power of Tilebond Ultimate wood glue View answer

Answer posted 7 years ago | Titebond III Ultimate Wood Glue

Question 39

will bearing BR-118 wok with router bit 23-140B and will that give me a 1/4 inch depth of cut View answer

Answer posted 7 years ago | Infinity Tools Slot Cutter w/ 1/4" Shank Arbor

Question 40

What diameter is the center opening? View answer

Answer posted 7 years ago | Infinity Tools Universal 7.5" Router Base Plate for Full SIze Routers

Question 41

Hey guys, I already have a collet extension. Is this kit available without that piece? View answer

Answer posted 7 years ago | Infinity Tools 6-pc. Tray Template Package

Question 42

Is it .030 or is it .035 thick, I am looking for a thicker one for a fence. The one I had was thicker View answer

Answer posted 7 years ago | Infinity Tools UHMW Slick Tape - .035" x 3" x 60" - Self Stick

Question 43

Can I get a 6 inch dado set with a 20 mm arbor for an Inca saw? View answer

Answer posted 7 years ago | Infinity Tools 3pc. Thick Kerf Flat-Top Saw Blade Package, 5/8" Arbor

Question 44

How do you change the saw blade without removing the bag? View answer

Answer posted 7 years ago | Milescraft Table Saw Dust Collector - Dust Cutter

Question 45

Will the Jasper 200 jig work with a Festool 1400 plunge router without any special modifications. View answer

Answer posted 7 years ago | Jasper Model 200 PRO Circle Guide

Question 46

Will this fit my Grizzly G1023RLW saw? View answer

Answer posted 7 years ago | Wixey 0" - 60" Digital Table Saw Fence Readout

Question 47

Can you use it to cut angles? View answer

Answer posted 7 years ago | INCRA Miter 5000 Table Saw Crosscut Sled

Question 48

Need a replacement for a cracked fixed roller on a Grizzly GO444Z saw. Can fixed rollers be swapped for swivel ones? View answer

Answer posted 7 years ago | Shop Fox Bear Crawl Heavy-Duty Mobile Base

Question 49

I've got a band saw that takes 108" blades. Is it the case that I can't get any of your blades in that size? View answer

Answer posted 7 years ago | Infinity Tools Resaw Bandsaw Blades

Question 50

Do you have support for DeWalt DCS361 miter saw zero clearance plate? View answer

Answer posted 7 years ago | Infinity Tools Zero Clearance Insert (Z.C.I.) Plate for DeWalt 10" & 12" Non-Sliding Saws

Browse by Topic

Tools