Infinity Cutting Tools Q&A
Can the Drill Press Precision Laser Guide and DRILLNADO be used together on the same drill press? View answer
Asked 5 ´years ago | Wixey Drill Press Precision Laser Guide
I am looking for a blade for 10 inch saw that can cut side ways for bee hive holes do u have anything View answer
Asked 5 ´years ago | Infinity Tools 8" Flat-Top Dado Saw Blade - 5/32" Kerf
Can the Triton TRA001 router be used with a Jessem Mast-R-Lift II right out of the box? View answer
Asked 5 ´years ago | Triton 3-1/4 HP Dual Mode Precision Plunge Router (TRA001)
What are the ID and OD of the largest part of the T fitting for the Triton 3.25 router dust collection kit? Is it 4"? View answer
Asked 5 ´years ago | Infinity Tools 3-Pc. Triton Router Dust Collection Package
Does the Mega Flush Trim Router bit come in 1/2" cutting Diam ? All I see is 3/4" or 1 1/2"? View answer
Asked 5 ´years ago | Infinity Tools 1/2" Shank Mega Flush Trim Router Bits
Can the top bearing be removed so the bottom bearing guides the cut? Needed for thickness greater than the bit’s cutting height? View answer
Do you make a 201"ù blade to fit the Laguna LT24? View answer
Asked 5 ´years ago | Infinity Tools Resaw Bandsaw Blades
If I want to join picture frames with 4 90 degree angles will the "Four Corner Adjustable Frame Clamp" suffice? View answer
Asked 5 ´years ago | Infinity Tools Adjustable Four Corner Frame Clamp
Can I cut 20 carbide planer blades to 18 for a WoodMaster 718 planer/molder, or do you have 18 blades available? Cutting 20 might be challenging. View answer
Asked 5 ´years ago | Infinity Tools Carbide Tipped Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets
Does this item qualify for free shipping to Franklin, NC 28734, or are there extra charges? View answer
Asked 5 ´years ago | Infinity Tools Carver's Vise
080-250 does this blade come in a 10 inch blade View answer
What are the dimensions of your stock guide? I have a Rigid R4513 saw with a 2? wide fence. Will it fit my jig? View answer
Asked 5 ´years ago | JessEm Clear-Cut Table Saw Stock Guides
Can I buy just the table without the fence? View answer
Asked 5 ´years ago | Infinity Tools Pro Router Table Package with Triton 3-1/4 HP Router (TRA001)
I need a router bit for 4” deep mortise pockets in oak stave core stiles. Do you have suitable bits or suggestions? View answer
Asked 5 ´years ago | Infinity Tools 1/4" Shank Mortise & Tenon Router Bits
Looking to buy 8"flat bottom cross cutting blade ,24 teeth,1/4" kerf,1" bore View answer
Asked 5 ´years ago | Infinity Tools Box Joint Jig Package with 1/4" Kerf Flat Top Blade and Setup Block Kit
Will Item # TSRP-029 fit my Ridgid TS3650 table saw. View answer
Asked 5 ´years ago | Infinity Tools Table Saw Router Table Package w/ 27" x 29" Table Top & 3.25HP Triton Router (TRA001)
Is this recommended for SawStop cabinet saws? If not, can you suggest another option? View answer
Asked 5 ´years ago | Infinity Tools Dadonator Jr., 6" Stacked Dado Saw Blade Set, 5/8" Bore
How do I operate multiple tools without switching plugs? Do I need multiple boxes or does this control one tool? View answer
Asked 5 ´years ago | iVac Automatic Vacuum Switch Box
I have a Bosch plunge router with inlay bushing kit and 1/8th bit. Will this work with your templates? Thanks View answer
Asked 5 ´years ago | Infinity Tools Nested Cross - Multi-Layer Inlay System
Will this insert fit Makita XSL04PTU View answer
Asked 5 ´years ago | Wooster White China Bristle 2"
Is the base plate compatible with a Festool OF1400? View answer
Asked 5 ´years ago | Cortador de círculos y ovalados con base de vacío Infinity Tools
Will this work on a Porter Cable 14" band saw View answer
Asked 5 ´years ago | Infinity Tools PRO-Grip Universal Fence Attachment
Do your Universal Base Plates for compact routers fit DeWalt 18V (20V USA) models? The USA model is 611, Australian 604. View answer
Asked 5 ´years ago | Infinity Tools Universal D-Handle Router Base Plate For Compact Routers
Will the Woodpecker Superfence work with this table? View answer
Asked 5 ´years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand
Does the 10" Super General thin kerf 10-045 blade work in a SawStop? View answer
Asked 5 ´years ago | Infinity Tools 10" Super General Combination Table Saw Blade
Will this table fit a Jet 12" bench top drill press? View answer
Asked 5 ´years ago | Infinity Tools Drill Press Table Packages
Will this work on a Lee Valley miter bit with a 1/2” shank and 1 3/4” diameter? Do you ship to Canada? View answer
Asked 5 ´years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock
Can Tongue & Groove Router Bits For Thin Stock be used at a 45-degree angle or only on butt joint corners? View answer
Asked 5 ´years ago | Infinity Tools 1/2" Shank Tongue & Groove For 3/8" to 5/8" Stock
How long is the portion that fit's in the dog holes as mine are not drilled all the way thru the table? View answer
Asked 5 ´years ago | BORA Self Adjusting In-Line Dog Clamp
Will this work with a Ridgid Table Saw Model #4513? View answer
Did You have only with 110 V or also option with 230 V ? View answer
When adding edge banding, how do you remove all the tops? Is unscrewing required? View answer
Asked 5 ´years ago | Mobile Miter Saw Station Plans
How and where do I use Odie’s Solvent with their wood products? Need more info. View answer
Asked 5 ´years ago | Abrazadera de marco ajustable Infinity Tools con diseño exclusivo de tuerca de velocidad
Is there ring to fit the eBush for the Leigh RTJ400 for a Bosch Router table RA1181 ? View answer
Asked 5 ´years ago | Leigh Router Table Dovetail Jig
Will the baseplate work with the festool OF 1400? View answer
Asked 5 ´years ago | Infinity Tools Universal 7.5" Router Base Plate
Does Infinity Tools provide Vetric vCarve "Tool" files for their CNC and other router bits? View answer
Asked 5 ´years ago | Infinity Tools 9-Pc. General Purpose C.N.C. Router Bit Set w/ Custom Case
The Evergreen Tree inlay shows three tree sizes. Which one is the 4” tree, and do you offer the other sizes? View answer
Asked 5 ´years ago | Infinity Tools - Árbol de pino de 4" - Sistema de incrustaciones multicapa
Will the Thin-Rip Guide For Table Saw; Bandsaw & Router Table work with my Bosch 4100 saw? View answer
Asked 5 ´years ago | Infinity Tools Thin-Rip Guide For Table Saw, Bandsaw & Router Table
Does the RTT-047 table accept the Jessem Rout-R-Lift? Can the Woodpeckers Superfence be used with it? View answer
What are the vise dimensions? How far do the jaws open and what width are they? Is this a standard luthier’s vise? View answer
Could you make a biscuit cutter for a number 11 biscuit View answer
Asked 5 ´years ago | Infinity Tools 3-Wing Slot Cutter, 5/16" I.D. x 1-7/8" O.D.
Can a 1 1/4" bore 2" glue joint cutter run on a 3/4" spindle Powermatic shaper? View answer
Asked 5 ´years ago | Infinity Tools Insert Pro Reverse Glue Joint Shaper Cutter, 1-1/4" Bore
Looking for a larger bit set for 2 thick window sash with 1 profile. Do you have a suitable set for this job? View answer
Asked 5 ´years ago | Infinity Tools 1/2" Shank Window Sash Router Bit Sets
Can the iVac 7-piece pack work with a 220v dust collector, planer, jointer, and a 120v miter saw? Can I add more gates? View answer
Asked 5 ´years ago | iVac 7-Pc. Auto Dust Collection Pack w/ 115 VAC Switch
For full bullnose on 1-1/32 thick oak stair treads, should I use a 1-1/8 bullnose bit or a 3/4 round over bit? View answer
Asked 5 ´years ago | Infinity Tools 1/2" Shank Bullnose Router Bits
Hello... Would these bits work for 3/8" thick hardwood material? View answer
Asked 5 ´years ago | Infinity Tools 1/2" Shank Lapped Miter Joint Router Bit Set w/ 3/4" Setup Block
Would like to know if this tool comes in 72 and 96 inch View answer
Asked 5 ´years ago | iGaging 0" - 36" Digital Table Saw Fence Readout
Do you have a quick change chuck to fit a SKIL 1845-02 2 HP Classic Series Variable Speed Plunge Router? View answer
Asked 5 ´years ago | Infinity Tools Eliminator Quick Change Router Chucks
Can it be used with a dewalt router and can it be set up for a router table? View answer
Asked 5 ´years ago | Infinity Tools Precision Router Dado Jig
Do you have a Canadian distributor for the Lock Miter Master jig, or do you ship to Canada? What are the shipping costs? View answer
Infinity Cutting Tools Q&A
