Question 1

Can the Drill Press Precision Laser Guide and DRILLNADO be used together on the same drill press? View answer

Answer posted 5 years ago | Wixey Drill Press Precision Laser Guide

Question 2

I am looking for a blade for 10 inch saw that can cut side ways for bee hive holes do u have anything View answer

Answer posted 5 years ago | Infinity Tools 8" Flat-Top Dado Saw Blade - 5/32" Kerf

Question 3

Can the Triton TRA001 router be used with a Jessem Mast-R-Lift II right out of the box? View answer

Answer posted 5 years ago | Triton 3-1/4 HP Dual Mode Precision Plunge Router (TRA001)

Question 4

What are the ID and OD of the largest part of the T fitting for the Triton 3.25 router dust collection kit? Is it 4"? View answer

Answer posted 5 years ago | Infinity Tools 3-Pc. Triton Router Dust Collection Package

Question 5

Does the Mega Flush Trim Router bit come in 1/2" cutting Diam ? All I see is 3/4" or 1 1/2"? View answer

Answer posted 5 years ago | Infinity Tools 1/2" Shank Mega Flush Trim Router Bits

Question 6

Can the top bearing be removed so the bottom bearing guides the cut? Needed for thickness greater than the bit’s cutting height? View answer

Answer posted 5 years ago | Infinity Tools 1/2" Shank Mega Flush Trim Router Bits

Question 7

Do you make a 201"ù blade to fit the Laguna LT24? View answer

Answer posted 5 years ago | Infinity Tools Resaw Bandsaw Blades

Question 8

If I want to join picture frames with 4 90 degree angles will the "Four Corner Adjustable Frame Clamp" suffice? View answer

Answer posted 5 years ago | Infinity Tools Adjustable Four Corner Frame Clamp

Question 9

Does this item qualify for free shipping to Franklin, NC 28734, or are there extra charges? View answer

Answer posted 5 years ago | Infinity Tools Carver's Vise

Question 10

I need a router bit for 4” deep mortise pockets in oak stave core stiles. Do you have suitable bits or suggestions? View answer

Answer posted 5 years ago | Infinity Tools 1/4" Shank Mortise & Tenon Router Bits

Question 11

080-250 does this blade come in a 10 inch blade View answer

Answer posted 5 years ago | Infinity Tools 8" Flat-Top Dado Saw Blade - 5/32" Kerf

Question 12

What are the dimensions of your stock guide? I have a Rigid R4513 saw with a 2? wide fence. Will it fit my jig? View answer

Answer posted 5 years ago | JessEm Clear-Cut Table Saw Stock Guides

Question 13

Can I buy just the table without the fence? View answer

Answer posted 5 years ago | Infinity Tools Pro Router Table Package with Triton 3-1/4 HP Router (TRA001)

Question 14

Can I cut 20 carbide planer blades to 18 for a WoodMaster 718 planer/molder, or do you have 18 blades available? Cutting 20 might be challenging. View answer

Answer posted 5 years ago | Infinity Tools Carbide Tipped Planer & Jointer Knives, 1/8" Thick, 3-Pc. Sets

Question 15

Looking to buy 8"flat bottom cross cutting blade ,24 teeth,1/4" kerf,1" bore View answer

Answer posted 5 years ago | Infinity Tools Box Joint Jig Package with 1/4" Kerf Flat Top Blade and Setup Block Kit

Question 16

Will Item # TSRP-029 fit my Ridgid TS3650 table saw. View answer

Answer posted 5 years ago | Infinity Tools Table Saw Router Table Package w/ 27" x 29" Table Top & 3.25HP Triton Router (TRA001)

Question 17

How do I operate multiple tools without switching plugs? Do I need multiple boxes or does this control one tool? View answer

Answer posted 5 years ago | iVac Automatic Vacuum Switch Box

Question 18

I have a Bosch plunge router with inlay bushing kit and 1/8th bit. Will this work with your templates? Thanks View answer

Answer posted 5 years ago | Infinity Tools Nested Cross - Multi-Layer Inlay System

Question 19

Is this recommended for SawStop cabinet saws? If not, can you suggest another option? View answer

Answer posted 5 years ago | Infinity Tools Dadonator Jr., 6" Stacked Dado Saw Blade Set, 5/8" Bore

Question 20

Will this insert fit Makita XSL04PTU View answer

Answer posted 5 years ago | Wooster White China Bristle 2"

Question 21

Is the base plate compatible with a Festool OF1400? View answer

Answer posted 5 years ago | Cortador de círculos y ovalados con base de vacío Infinity Tools

Question 22

Will this work on a Porter Cable 14" band saw View answer

Answer posted 5 years ago | Infinity Tools PRO-Grip Universal Fence Attachment

Question 23

Do your Universal Base Plates for compact routers fit DeWalt 18V (20V USA) models? The USA model is 611, Australian 604. View answer

Answer posted 5 years ago | Infinity Tools Universal D-Handle Router Base Plate For Compact Routers

Question 24

Will the Woodpecker Superfence work with this table? View answer

Answer posted 5 years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 25

Does the 10" Super General thin kerf 10-045 blade work in a SawStop? View answer

Answer posted 5 years ago | Infinity Tools 10" Super General Combination Table Saw Blade

Question 26

Will this table fit a Jet 12" bench top drill press? View answer

Answer posted 5 years ago | Infinity Tools Drill Press Table Packages

Question 27

Will this work on a Lee Valley miter bit with a 1/2” shank and 1 3/4” diameter? Do you ship to Canada? View answer

Answer posted 5 years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Question 28

Can Tongue & Groove Router Bits For Thin Stock be used at a 45-degree angle or only on butt joint corners? View answer

Answer posted 5 years ago | Infinity Tools 1/2" Shank Tongue & Groove For 3/8" to 5/8" Stock

Question 29

How long is the portion that fit's in the dog holes as mine are not drilled all the way thru the table? View answer

Answer posted 5 years ago | BORA Self Adjusting In-Line Dog Clamp

Question 30

Will this work with a Ridgid Table Saw Model #4513? View answer

Answer posted 5 years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 31

Did You have only with 110 V or also option with 230 V ? View answer

Answer posted 5 years ago | Triton 3-1/4 HP Dual Mode Precision Plunge Router (TRA001)

Question 32

When adding edge banding, how do you remove all the tops? Is unscrewing required? View answer

Answer posted 5 years ago | Mobile Miter Saw Station Plans

Question 33

Is there ring to fit the eBush for the Leigh RTJ400 for a Bosch Router table RA1181 ? View answer

Answer posted 5 years ago | Leigh Router Table Dovetail Jig

Question 34

Will the baseplate work with the festool OF 1400? View answer

Answer posted 5 years ago | Infinity Tools Universal 7.5" Router Base Plate

Question 35

How and where do I use Odie’s Solvent with their wood products? Need more info. View answer

Answer posted 5 years ago | Abrazadera de marco ajustable Infinity Tools con diseño exclusivo de tuerca de velocidad

Question 36

Does Infinity Tools provide Vetric vCarve "Tool" files for their CNC and other router bits? View answer

Answer posted 5 years ago | Infinity Tools 9-Pc. General Purpose C.N.C. Router Bit Set w/ Custom Case

Question 37

The Evergreen Tree inlay shows three tree sizes. Which one is the 4” tree, and do you offer the other sizes? View answer

Answer posted 5 years ago | Infinity Tools - Árbol de pino de 4" - Sistema de incrustaciones multicapa

Question 38

Will the Thin-Rip Guide For Table Saw; Bandsaw & Router Table work with my Bosch 4100 saw? View answer

Answer posted 5 years ago | Infinity Tools Thin-Rip Guide For Table Saw, Bandsaw & Router Table

Question 39

Does the RTT-047 table accept the Jessem Rout-R-Lift? Can the Woodpeckers Superfence be used with it? View answer

Answer posted 5 years ago | Infinity Tools 27" x 29" Table Saw Router Table & Stand

Question 40

What are the vise dimensions? How far do the jaws open and what width are they? Is this a standard luthier’s vise? View answer

Answer posted 5 years ago | Infinity Tools Carver's Vise

Question 41

Can a 1 1/4" bore 2" glue joint cutter run on a 3/4" spindle Powermatic shaper? View answer

Answer posted 5 years ago | Infinity Tools Insert Pro Reverse Glue Joint Shaper Cutter, 1-1/4" Bore

Question 42

Could you make a biscuit cutter for a number 11 biscuit View answer

Answer posted 5 years ago | Infinity Tools 3-Wing Slot Cutter, 5/16" I.D. x 1-7/8" O.D.

Question 43

Looking for a larger bit set for 2 thick window sash with 1 profile. Do you have a suitable set for this job? View answer

Answer posted 5 years ago | Infinity Tools 1/2" Shank Window Sash Router Bit Sets

Question 44

Can the iVac 7-piece pack work with a 220v dust collector, planer, jointer, and a 120v miter saw? Can I add more gates? View answer

Answer posted 5 years ago | iVac 7-Pc. Auto Dust Collection Pack w/ 115 VAC Switch

Question 45

For full bullnose on 1-1/32 thick oak stair treads, should I use a 1-1/8 bullnose bit or a 3/4 round over bit? View answer

Answer posted 5 years ago | Infinity Tools 1/2" Shank Bullnose Router Bits

Question 46

Hello... Would these bits work for 3/8" thick hardwood material? View answer

Answer posted 5 years ago | Infinity Tools 1/2" Shank Lapped Miter Joint Router Bit Set w/ 3/4" Setup Block

Question 47

Would like to know if this tool comes in 72 and 96 inch View answer

Answer posted 5 years ago | iGaging 0" - 36" Digital Table Saw Fence Readout

Question 48

Do you have a quick change chuck to fit a SKIL 1845-02 2 HP Classic Series Variable Speed Plunge Router? View answer

Answer posted 5 years ago | Infinity Tools Eliminator Quick Change Router Chucks

Question 49

Can it be used with a dewalt router and can it be set up for a router table? View answer

Answer posted 5 years ago | Infinity Tools Precision Router Dado Jig

Question 50

Do you have a Canadian distributor for the Lock Miter Master jig, or do you ship to Canada? What are the shipping costs? View answer

Answer posted 5 years ago | Infinity Tools 2-Pc. Lock Miter Master Jig Set - For 3/8" - 1-3/16" Stock

Browse by Topic

Tools